Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›

Home office gear, compared spec by spec.

Amazon Black Friday Week deals
Audio, Power and Connectivity

Can You Make Wired Speakers Wireless? Yes, With a Receiver

Yes, a Bluetooth receiver plugs into your amp or powered speakers and adds wireless streaming, and this guide shows how to match it, plug it in and pair it.

Can You Make Wired Speakers Wireless? Yes, With a Receiver

Your wired speakers still sound fine, but the phone stays tethered to the desk by a cable, and every playlist change means reaching across the keyboard. Can you make wired speakers wireless? Yes. A small Bluetooth receiver plugs into the amplifier or powered speakers and takes music from your phone over the air, so the speakers stay put and the cable to the phone goes away.

OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

Can you make wired speakers wireless?

Yes, with a receiver in the middle. A Bluetooth receiver takes the wireless signal from a phone, tablet or laptop and hands it to the wired system through a cable: RCA, 3.5mm, optical or XLR, depending on the model. The speakers keep their own amplifier and power, and the receiver only replaces the wire between the phone and the amp. A receiver is not a transmitter: it receives Bluetooth audio and sends it out over a cable, so it cannot send sound from a stereo to Bluetooth headphones.

Step 1: Check what your speakers plug into

Start at the back of the amplifier or the powered speakers and list the spare inputs. Most receivers offer RCA or 3.5mm outputs: the 1Mii B06 (on Amazon)+ plugs into computer speakers or a home stereo through 3.5mm or RCA, and the esinkin adapter uses standard RCA or 3.5mm jacks. The KAIY C36 adds an optical output beside RCA and 3.5mm, the Audioengine B1 (on Amazon) offers RCA and optical outputs, and the blafili B3 (on Amazon) offers RCA, balanced XLR, optical and coaxial outputs, with all 4 outputs usable at the same time. Match the receiver to an input your system already has.

Step 2: Pick a receiver for range and sound

Bluetooth version and range decide how far the phone can roam. The KAIY C53 and the KAIY C36 list a range of up to 33 feet, the esinkin lists up to 15 meters or 50 feet, and the Xvive P3 (on Amazon) lists up to 30 meters. The 1Mii B06+ lists up to 98 ft in open air and 50 to 70 ft indoors, the Audioengine B1 and the 1Mii DS200Pro (on Amazon) list up to 100 ft, the blafili B3 lists up to 33 m, and the DS18 BTC-Five lists up to 130 feet. Walls and obstacles shorten the range. For sound, the UGREEN receiver supports LDAC with audio sampling rates up to 24bit/96KHz, the blafili B3 supports LDAC, aptX HD, aptX Low Latency, aptX, SBC and AAC, and the 1Mii B06+ supports aptX HD and aptX Adaptive.

Step 3: Plug it in and pair it

Power the receiver first, then connect the audio cable to a spare input on the amplifier or powered speakers. The 1Mii B06+ comes with a USB power adapter, the KAIY C53 comes with a USB cable that plugs into any USB outlet or phone charger, and the KAIY C36 runs from a standard 5V/1A wall adapter. Pair the phone from its Bluetooth menu, then play music and set the volume on both the phone and the amp. The 1Mii B06+ powers on automatically and reconnects with the paired device, the KAIY C53 pairs automatically every time it powers on The 1Mii B06+ and the UGREEN receiver each pair with 2 devices at once, while the KAIY C36 connects to one device at a time.

Step 4: Keep it powered

Some receivers run on a battery and some need a cable at all times. The Xvive P3 has a rechargeable battery with up to 8 hours of use on a single charge, and the UGREEN receiver gives up to 15 hours of playback and takes 2 hours to charge fully, and it works while charging. The KAIY C36 has no battery inside, so connect the power supply before use. The KAIY C36 also sleeps if no audio plays for 10 minutes.

What a receiver cannot do

A receiver adds Bluetooth input, and nothing else. The blafili B3 cannot drive passive speakers directly, so passive speakers still need an amplifier between the receiver and the cones. The KAIY C53 and the esinkin adapter are receivers only, not transmitters, so neither one sends audio to Bluetooth headphones. The KAIY C53 cannot turn wired headphones wireless, and the KAIY C36 is not for Bluetooth headphones either.

FAQ

Do I need an amplifier for passive speakers?

Yes. A Bluetooth receiver cannot drive passive speakers directly, as the blafili B3 listing states, so plug the receiver into an amplifier and let the amplifier drive the speakers.

How far can I walk from the receiver?

It depends on the model and the walls between the phone and the receiver. The 1Mii B06+ lists up to 98 ft in open air and 50 to 70 ft indoors, the Audioengine B1 lists up to 100 feet, and the DS18 BTC-Five lists up to 130 feet. The KAIY C53 lists up to 33 feet.

Can I connect two phones at once?

Some receivers can. The 1Mii B06+ pairs with 2 devices at once and switches between them without re-pairing, and the UGREEN receiver also supports connecting 2 phones at once. The KAIY C36 connects to one device at a time, so check the listing when two people share the speakers.

Does a receiver need power?

Yes, from a cable or a battery. The 1Mii B06+ comes with a USB power adapter, the KAIY C53 runs from a USB cable, and the KAIY C36 needs a 5V/1A wall adapter. The Xvive P3 runs up to 8 hours on its battery, and the UGREEN receiver runs up to 15 hours.

Will the receiver work with my phone?

Yes, when the phone has Bluetooth. The 1Mii B06+ streams from a phone, tablet or laptop, the KAIY C53 pairs by NFC when the phone supports it, and the 1Mii B06+ also works with voice commands through an Echo.

More for your workspace

See the best Bluetooth adapters for old receivers, the best high-quality Bluetooth speakers, the types of audio cables and the best audio interfaces.