Condenser microphone setup means mounting the mic on a desk stand, pointing it at your mouth, and adding a pop filter and a shock mount before you record. A mic on the bare desk picks up bumps and breath noise, and a stand that holds the mic steady keeps your voice clear while you talk. The steps below work through each move with the stands the listings describe.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
The quick answer
Mount the mic on a desk stand at mouth height, fit the shock mount and the pop filter, and point the mic at your mouth. The InnoGear stand adjusts from 8.0 to 12.8 inches, the JCWINY tripod (on Amazon) from 11.5 to 18 inches, the Frgyee stand (on Amazon) from 6.3 to 9.5 inches, and the On-Stage stand from 9 to 13 inches.
Step 1: Fit the mic to the stand
Check the thread and the clip size before you buy. The InnoGear stand comes with a 3/8 inch to 5/8 inch adapter and a mic clip that takes mics up to 1.26 inch in diameter, so it fits Blue Yeti, HyperX QuadCast, Fifine, AT2020 and Razer Seiren X. The JCWINY kit comes with a 1/4 inch to 5/8 inch adapter that fits Blue Yeti, Shure SM7B, Rode PodMic, AT2020 and Razer Seiren X. The Frgyee stand is made for mics of 1.8 to 2 inches in diameter, and the On-Stage stand mounts standard mic clips and accessories with 5/8 inch, 27 threading.
Step 2: Set the height
Raise the stand so the mic sits at mouth height. The InnoGear stand adjusts from 8.0 to 12.8 inches with a screw-in adjustment knob, the On-Stage stand from 9 to 13 inches, the Frgyee stand from 6.3 to 9.5 inches, and the JCWINY tripod from 11.5 to 18 inches on 2 adjustable levels. Pick the range that puts the mic at your mouth.
Step 3: Add the shock mount and the pop filter
Fit the shock mount around the mic, then set the pop filter between the mic and your mouth. The Frgyee shock mount uses suspension straps and high elastic winding rope, and its foam windscreen filters dust, noise and wind interference. The JCWINY shock mount fits mics of 40 to 52 mm, and its double layer pop filter sits on a gooseneck that turns 360 degrees. The InnoGear and On-Stage stands list no shock mount or pop filter, so add those parts on their own when you use those stands.
Step 4: Point the mic and record a short check
Point the mic at your mouth and record a short clip. Listen for bumps from the desk, pops on hard sounds and hiss from the room. If the mic picks up desk noise, check that the base sits flat: the InnoGear base has 4 non-slip rubber pads and the Frgyee base has a bottom sponge pad.
The gear
The 4 stands below cover Blue Yeti, AT2020, Shure and Fifine mics, with height ranges from 6.3 to 18 inches and shock mounts in 2 of the kits, ranked by the scores their listings earn.
| # | Product | Office Score | Buy |
|---|---|---|---|
| 1 | InnoGear Desktop Mic Stand | 9.7/10 | Buy on Amazon |
| 2 | JCWINY Desk Mic Stand Kit | 9.7/10 | Buy on Amazon |
| 3 | Frgyee AT2020 Desktop Mic Stand | 9.6/10 | Buy on Amazon |
| 4 | On-Stage DS7200B Mic Stand | 9.4/10 | Buy on Amazon |

InnoGear Desktop Mic Stand
A metal desk mic stand with a weighted 5.12 inch base and a height range of 8.0 to 12.8 inches for Blue Yeti, Shure and Fifine mics.
Pros
- Adjusts from 8.0 to 12.8 inches
- Holds mics up to 3.3 lbs
- 5.12 inch metal base, 1.85 lbs, with 4 non-slip rubber pads
- 3/8 inch to 5/8 inch adapter fits Blue Yeti, AT2020 and Shure mics
Cons
- Warranty term is not clearly stated in the listing
- Clip fits mics up to 1.26 inch diameter only
- Base is 5.12 inches wide and needs desk space
- No pop filter or shock mount is included
Detailed Review
InnoGear lists a desktop microphone stand with a solid metal base measuring 5.12 inches in diameter, with 4 non-slip rubber pads. Height adjusts from 8.0 to 12.8 inches with a screw-in adjustment knob, and the stand holds mics and accessories weighing up to 3.3 lbs. A 3/8 inch to 5/8 inch adapter fits Blue Yeti, HyperX QuadCast, Fifine, AT2020 and Razer Seiren X, and the included clip takes mics up to 1.26 inch in diameter.
Who it's for: owners of a Blue Yeti, AT2020 or Fifine mic who want a heavy base and a wide height range. Who should skip it: owners who need a pop filter or a shock mount in the box.
Its Office Score of 9.7/10 comes from performance 33/35, build 22/25, value 21/25, safety 8/10 and warranty 0/5: 84 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Base | 5.12 inch diameter, 1.85 lbs |
|---|---|
| Height | 8.0 to 12.8 inches |
| Capacity | 3.3 lbs |
| Adapter | 3/8 inch to 5/8 inch |
These specs mirror the retailer listing as of 14 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. Solid metal base with 4 non-slip rubber pads and a screw-in adjustment knob that holds the set height, so safety scores 8 of 10. No warranty term, so warranty scores zero. See How We Pick.
Protect your hearing. Keep volume moderate during long calls, take breaks, and treat noise cancelling and battery figures as the maker's claims.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

JCWINY Desk Mic Stand Kit
A tripod desk mic stand kit with a pop filter, shock mount and mic clip, with height from 11.5 to 18 inches.
Pros
- Complete kit: stand, pop filter, shock mount, clip and adapter
- Height extends from 11.5 to 18 inches, the tallest range here
- Double layer pop filter on a 360 degree gooseneck
- Tripod design with the center of gravity dropping in use
Cons
- Shock mount does not fit Blue Yeti, per the listing
- Shock mount fits mics of 40 to 52 mm only
- Warranty term is not clearly stated in the listing
- Tripod legs take more desk space than a round base
Detailed Review
JCWINY lists a desk microphone stand kit with a stand, a pop filter, a shock mount, a mic clip and an adapter. Height extends from 11.5 to 18 inches, and the tripod design keeps the center of gravity dropping in use. The double layer pop filter sits on a gooseneck that turns 360 degrees, and the shock mount fits mics with an outer diameter of 40 to 52 mm, though it does not fit Blue Yeti.
Who it's for: owners who want the full kit in one box and the tallest height range here. Who should skip it: Blue Yeti owners who need the shock mount.
Its Office Score of 9.7/10 comes from performance 32/35, build 21/25, value 22/25, safety 7/10 and warranty 0/5: 82 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Height | 11.5 to 18 inches |
|---|---|
| Shock mount | 40 to 52 mm |
| Gooseneck | 360 degrees |
| Kit | Stand, pop filter, shock mount, mic clip, adapter |
These specs mirror the retailer listing as of 14 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. Tripod design with the center of gravity dropping in use and a shock mount with high elasticity wrap roping, so safety scores 7 of 10. No warranty term, so warranty scores zero. See How We Pick.
Protect your hearing. Keep volume moderate during long calls, take breaks, and treat noise cancelling and battery figures as the maker's claims.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

Frgyee AT2020 Desktop Mic Stand
A desktop stand made for the Audio Technica AT2020, with a shock mount, a foam windscreen and a metal weighted base.
Pros
- Made for the AT2020, AT2020USB, AT2035 and ATR2500
- Shock mount with suspension straps and high elastic winding rope
- Foam windscreen filters dust, noise and wind interference
- Metal weighted base with a bottom sponge pad
Cons
- Height range of 6.3 to 9.5 inches is the lowest here
- Fits mics of 1.8 to 2 inches in diameter only
- Warranty term is not clearly stated in the listing
- Base is 5.2 by 5.2 inches and needs a flat spot
Detailed Review
Frgyee lists a desktop mic stand made for the Audio Technica AT2020, and for the AT2020USB, AT2020USB+, AT2035 and ATR2500. The stand bar adjusts from 6.3 to 9.5 inches, and the metal weighted base has a bottom sponge pad that stops noise and scratches. The shock mount uses suspension straps and high elastic winding rope, and the foam windscreen filters dust, noise and wind interference.
Who it's for: AT2020 owners who want a shock mount and a windscreen in the box. Who should skip it: owners of mics wider than 2 inches.
Its Office Score of 9.6/10 comes from performance 29/35, build 20/25, value 20/25, safety 7/10 and warranty 0/5: 76 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Height | 6.3 to 9.5 inches |
|---|---|
| Mic diameter | 1.8 to 2 inches |
| Base | 5.2 by 5.2 inches |
| Included | Shock mount and foam windscreen |
These specs mirror the retailer listing as of 14 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. Metal weighted base with a bottom sponge pad and a shock mount with suspension straps, so safety scores 7 of 10. No warranty term, so warranty scores zero. See How We Pick.
Protect your hearing. Keep volume moderate during long calls, take breaks, and treat noise cancelling and battery figures as the maker's claims.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

On-Stage DS7200B Mic Stand
A compact adjustable desktop mic stand with a round weighted base and a height range of 9 to 13 inches.
Pros
- Adjusts from 9 to 13 inches for short-height miking
- Round weighted base fits desks, tables and podiums
- Durable black finish resists chips and scratches
- Mounts standard mic clips and accessories with 5/8 inch, 27 threading
Cons
- No shock mount, pop filter or clip is included
- Listing states few facts beyond height and base
- Warranty term is not clearly stated in the listing
- No weight capacity is stated
Detailed Review
On-Stage lists the DS7200B as an adjustable desktop mic stand for short-height miking, with a round weighted base and a durable black finish. Height adjusts from 9 to 13 inches, and the stand mounts standard mic clips and accessories with 5/8 inch, 27 threading. The listing states no weight capacity, no base size and no warranty term beyond a manufacturer warranty.
Who it's for: owners who already have a mic clip and want a plain, compact stand. Who should skip it: owners who need a shock mount, a pop filter or a stated weight capacity.
Its Office Score of 9.4/10 comes from performance 26/35, build 19/25, value 19/25, safety 5/10 and warranty 0/5: 69 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Height | 9 to 13 inches |
|---|---|
| Threading | 5/8 inch, 27 threading |
| Finish | Black, resists chips and scratches |
| Base | Round weighted base |
These specs mirror the retailer listing as of 14 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. Round weighted base and a durable black finish that resists chips and scratches, so safety scores 5 of 10. No warranty term, so warranty scores zero. See How We Pick.
Protect your hearing. Keep volume moderate during long calls, take breaks, and treat noise cancelling and battery figures as the maker's claims.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.
As an Amazon Associate I earn from qualifying purchases.
Condenser microphone setup: pick the right stand
Height range
The JCWINY tripod reaches 11.5 to 18 inches, the tallest range here, and the On-Stage stand reaches 9 to 13 inches. The InnoGear stand covers 8.0 to 12.8 inches, and the Frgyee stand covers 6.3 to 9.5 inches.
Shock mount and pop filter
Only 2 kits include them. The Frgyee kit includes a shock mount and a foam windscreen, and the JCWINY kit includes a shock mount and a double layer pop filter. The InnoGear and On-Stage stands list neither, so plan to add them on their own.
Compatibility
The Frgyee stand is made for the AT2020 and mics of 1.8 to 2 inches in diameter. The InnoGear and JCWINY stands list Blue Yeti, AT2020, Shure and Razer mics, and the JCWINY shock mount does not fit Blue Yeti, per the listing. See Monitor Mounts, Keyboards and Mice for more desk gear.
FAQ
Can I use a condenser mic without a stand?
You can hold it, but a stand keeps the mic at mouth height and stops desk bumps from reaching the mic.
What height should the mic sit at?
At mouth height while you sit at the desk. The stands here adjust from 6.3 to 18 inches across the 4 listings, so pick the range that reaches your mouth.
Do I need a pop filter?
A pop filter blocks air blasts. The JCWINY kit includes a double layer pop filter, and the Frgyee kit includes a foam windscreen that filters wind interference and spit spray.
Which stand fits an Audio Technica AT2020?
The Frgyee stand is made for the AT2020, AT2020USB, AT2035 and ATR2500. The InnoGear and JCWINY stands also list the AT2020 among the mics they fit.
Score breakdown
The Office Score weighs performance, build, value, safety and warranty. For mic stands, safety means a base that keeps the mic upright and a shock mount that blocks vibration. None of the 4 listings states a clear warranty term, so warranty scores 0 across the board. How we pick explains the weights.
More for your workspace
See every Monitor Mounts, Keyboards and Mice guide and all Webcams and Ring Lights guides.









