The drawer glides open on its own whenever the cabinet is nudged, and the key turns in a full circle without catching, so nothing inside the drawer stays shut. That loose, spinning key is the usual sign that the cylinder or the cam behind it has worn past the point where it can grip, and file cabinet lock repair starts with finding which part has failed. This guide walks through the checks, the measurements and the replacement parts that put the drawer back under lock, with the gear below matched to each stage.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
The quick answer
File cabinet lock repair means finding whether the key, the cylinder or the cam has failed, then replacing the failed part with a cam lock that matches the door thickness and the keyhole size. A key that turns freely with no resistance points to a worn cylinder or a loose cam, while a key that will not turn points to a cylinder that has seized or a key that no longer matches the pins inside. Measure the cam lock body length, the door panel thickness and the keyhole diameter before ordering, and match the replacement to those measurements.
Check the key and the cylinder
Start with the key itself. A bent or worn key can fail to lift the pins, so compare it with any spare key from the same lock and look for a bent blade or a worn edge. If the spare key works and the usual key does not, the key is the failed part. If no key turns the cylinder, the cylinder itself is the likely fault, and a replacement lock is the next stage. Keep the failed key with the lock until the replacement arrives, so the size and the keyway can be compared side by side.
Measure before you order
A cam lock that does not match the door will not sit right, so measure the parts that the listing states. The Lhazemu listing states a body length of 5/8 in (16 mm), a maximum door panel thickness of 0.48 in (12.19 mm), a keyhole diameter of 0.7 in (18 mm) and a locking plate of 1.83 in (46.6 mm). Measure the door panel at the lock hole and the keyhole across its widest point, then check the figures against the listing before ordering. The types of file cabinet locks guide explains how cam locks differ, which helps when the failed lock looks different from the listings here.
File cabinet lock repair: the gear for each stage
The cam locks below cover the stages above, from a full replacement lock with stated measurements to a HON kit and title-only locks for a straight swap where the size is already known.
| # | Product | Office Score | Buy |
|---|---|---|---|
| 1 | Lhazemu 5/8 Cam Lock | 9.6/10 | Buy on Amazon |
| 2 | Hecfu 5/8 in Cam Lock | 9.6/10 | Buy on Amazon |
| 3 | HOWDIA Drawer Lock 2 Pcs | 9.5/10 | Buy on Amazon |
| 4 | MSPowerstrange F26 Lock Kit | 9.4/10 | Buy on Amazon |

Lhazemu 5/8 Cam Lock
A keyed-alike cam lock with a 5/8 in body that handles the full replacement stage, with stated measurements for the door panel and the keyhole.
Pros
- Body length of 5/8 in (16 mm) is stated, with a locking plate of 1.83 in (46.6 mm)
- Maximum door panel thickness of 0.48 in (12.19 mm) and keyhole diameter of 0.7 in (18 mm) are stated
- The keys supplied operate the same lock, per the listing
- Metal construction is stated, and the listing names cabinets, drawers, toolboxes, trailers, RVs and mailboxes as uses
Cons
- No warranty term is stated
- No mounting hardware is named in the listing
- No cam shape or rotation detail is stated
Detailed Review
Lhazemu lists a 5/8 in cam lock body (16 mm) with a locking plate of 1.83 in (46.6 mm), a maximum door panel thickness of 0.48 in (12.19 mm) and a keyhole diameter of 0.7 in (18 mm). The listing states sturdy metal construction and keyed-alike operation, with uses across cabinets, desk drawers, toolboxes, trailers, RVs and mailboxes. The spec table gives product dimensions of 0.24 by 0.35 by 0.38 in, which do not match the stated body length, so the title and bullets carry the measurements here. It handles the measuring and replacement stage: the stated figures let the reader check the door and the keyhole before ordering.
Who it's for: someone replacing a cam lock who wants the body length, door thickness and keyhole size stated before ordering. Who should skip it: anyone whose door panel is thicker than 0.48 in or whose keyhole does not match 0.7 in.
Its Office Score of 9.6/10 comes from performance 29/35, build 21/25, value 21/25, safety 7/10 and warranty 0/5: 78 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Body length | 5/8 in (16 mm) |
|---|---|
| Door panel thickness, max | 0.48 in (12.19 mm) |
| Keyhole diameter | 0.7 in (18 mm) |
| Locking plate | 1.83 in (46.6 mm) |
These specs mirror the retailer listing as of 13 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. Sturdy metal construction and keyed-alike locking are stated, so safety scores 7 of 10. No warranty term, so warranty scores zero. See How We Pick.
Anchor it. Anchor tall bookshelves and file cabinets to the wall with the supplied hardware or an anti-tip kit, load the lowest shelves and drawers first, and open one drawer at a time.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

Hecfu 5/8 in Cam Lock
A chrome-plated zinc alloy cam lock, keyed alike, with a 5/8 in body for door panels up to 0.48 in thick.
Pros
- Chrome-plated zinc alloy construction, rust-proof per the listing
- Keyed alike: one key opens every lock in the order
- Fits door panels up to 0.48 in thick, with two lock plate sizes
- Opens at 90 degrees; key removable when locked or unlocked
Cons
- No warranty term is stated
- Single lock per pack; a full cabinet needs more than one set
- Door thickness limit of 0.48 in excludes thicker panels
Detailed Review
Hecfu lists a 1-pack cam lock, cast from chrome-plated zinc alloy, with a 5/8 in (16mm) body for door panels up to 0.48 in (12.19mm) thick and a keyhole diameter of about 0.7 in (18mm). The pack holds 1 lock body, 1 hex nut, 2 same keys, 2 lock plates at 1.83 in (46.6mm) and 1.38 in (35mm), and the lock opens at 90 degrees with the key removable when locked or unlocked. The spec table gives product dimensions of 0.63 x 0.7 x 0.7 in, which describe the lock body rather than the plates, so measure the plates from the bullets.
Who it's for: anyone replacing a cam lock on a filing cabinet, mailbox or RV compartment with a panel up to 0.48 in thick. Who should skip it: anyone with a thicker panel or who wants a different key per lock.
Its Office Score of 9.6/10 comes from performance 30/35, build 21/25, value 20/25, safety 5/10 and warranty 0/5: 76 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Body length | 5/8 in (16mm) |
|---|---|
| Door thickness | Up to 0.48 in (12.19mm) |
| Keyhole | About 0.7 in (18mm) |
| Plates | 1.83 in and 1.38 in |
Figures as published on the retailer listing, collected 6 November 2026. Performance figures are manufacturer rated.
Safety and Warranty
What this listing states. Keyed alike cam lock with two keys, two lock plates and a hex nut stated, so safety scores 5 of 10. No warranty term, so warranty scores zero. See How We Pick.
Anchor it. Anchor tall bookshelves and file cabinets to the wall with the supplied hardware or an anti-tip kit, load the lowest shelves and drawers first, and open one drawer at a time.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

HOWDIA Drawer Lock 2 Pcs
A 2-pack of zinc alloy drawer locks with a 16mm cylinder and a 40mm locking rod, keyed different.
Pros
- Zinc alloy with steel components and screws M4 x 16mm
- Fit figures: 16mm cylinder, 40mm locking rod, 30mm hole spacing
- Mounts to metal or wood, door or drawer panels
- 2-pack, keyed different: each lock has its own key
Cons
- No warranty term is stated
- Panel must be 18 to 20mm thick with a 16mm mounting hole
- Listing notes a possible 1-2mm error in the stated figures
- Keyed different means a separate key per lock
Detailed Review
HOWDIA lists a 2-pack of zinc alloy drawer locks with steel components and screws M4 x 16mm, a cylinder diameter of 16mm (5/8 in), a cylinder length of 20mm (3/4 in), a locking rod length of 40mm (1-9/16 in), a plate length of 44mm (1-3/4 in) and width of 20mm (13/16 in), and mounting hole spacing of 30mm (1-3/16 in). The panel must be 18 to 20mm thick with a 16mm mounting hole and no more than 40mm from panel to rod, and the listing notes a possible 1-2mm error in the figures. The keys are different per lock, and the locks mount to metal or wood, door or drawer panels.
Who it's for: anyone fitting a drawer lock to a panel that meets the stated 18 to 20mm thickness and 16mm hole. Who should skip it: anyone whose panel falls outside those figures or who wants one key for every lock.
Its Office Score of 9.5/10 comes from performance 28/35, build 21/25, value 20/25, safety 5/10 and warranty 0/5: 74 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Cylinder | 16mm diameter, 20mm length |
|---|---|
| Locking rod | 40mm |
| Panel | 18 to 20mm thick, 16mm hole |
| Weight | 0.22 pounds |
Figures as published on the retailer listing, collected 6 November 2026. Performance figures are manufacturer rated.
Safety and Warranty
What this listing states. Keyed different zinc alloy drawer locks with steel components stated, so safety scores 5 of 10. No warranty term, so warranty scores zero. See How We Pick.
Anchor it. Anchor tall bookshelves and file cabinets to the wall with the supplied hardware or an anti-tip kit, load the lowest shelves and drawers first, and open one drawer at a time.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

MSPowerstrange F26 Lock Kit
A push-in to lock kit in F26 style for HON file cabinets, for the replacement stage where the cabinet model is already known.
Pros
- Push-in to lock operation is stated in the title
- Made for HON file cabinets in F26 style, so the fit is named rather than guessed
- Item weight of 0.22 lb is stated in the spec table
- Silver finish is stated in the spec table
Cons
- The listing states no material
- The listing states no key count and no keyed-alike detail
- The listing states no door thickness or keyhole size
- No warranty term is stated
Detailed Review
MSPowerstrange lists a file cabinet lock kit for HON file cabinets in F26 style, with push-in to lock operation and the kit code SRS #2190. The spec table states a silver finish, an item weight of 0.22 lb and a model of F26, with product dimensions of 0.79 by 1.38 by 3.15 in. The listing states no material and no measurements for the door panel or the keyhole, so the reader must already know the F26 fit. It handles the replacement stage for a HON cabinet where the kit style is already known.
Who it's for: someone with a HON file cabinet who needs the F26 push-in kit. Who should skip it: anyone who needs stated measurements or a lock for a cabinet other than a HON file cabinet.
Its Office Score of 9.4/10 comes from performance 26/35, build 18/25, value 19/25, safety 5/10 and warranty 0/5: 68 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Model | F26 |
|---|---|
| Kit | SRS #2190, F26 style |
| Item weight | 0.22 lb |
| Color | Silver |
These specs mirror the retailer listing as of 13 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. Push-in to lock kit for HON file cabinets is stated, so safety scores 5 of 10. No warranty term, so warranty scores zero. See How We Pick.
Anchor it. Anchor tall bookshelves and file cabinets to the wall with the supplied hardware or an anti-tip kit, load the lowest shelves and drawers first, and open one drawer at a time.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.
As an Amazon Associate I earn from qualifying purchases.
When a replacement is the answer
When the cylinder has seized or the cam has worn past gripping, a new lock is the practical route. Match the body length and the door thickness from the measurements above, check that the locking plate reaches the strike area, and keep the old lock until the new lock is fitted, so the cam orientation can be copied. A lock that matches on every stated figure will seat in the same hole and turn the same way as the lock it replaces.
FAQ
Can a file cabinet lock be repaired without a replacement part?
Sometimes a loose cam can be tightened back onto the cylinder, but a worn cylinder or a key that no longer turns the lock calls for a replacement lock matched to the door measurements.
What size cam lock fits a file cabinet?
It depends on the door. The Lhazemu listing states a 5/8 in body for a door panel up to 0.48 in thick, with a 0.7 in keyhole, so measure the door panel and the keyhole and match those figures before ordering.
What does keyed alike mean?
It means the keys supplied with the lock operate the same lock, so a spare key from the same set opens the same cylinder. The Lhazemu listing states keyed-alike operation, and the Hecfu listing states the same in its title.
How do I know which lock kit fits a HON file cabinet?
Match the kit style to the cabinet. The MSPowerstrange listing is a file cabinet lock kit for HON file cabinets in F26 style, with push-in to lock operation and the kit code SRS #2190, so match the F26 style to the failed lock before ordering.
More for your workspace
See the types of file cabinet locks, the wood file cabinets with a lock and the storage cabinets that lock.









