The cabinet in the spare room was supposed to hold the printer, the paper and the spare cables, but the shelf sat at the wrong height from the day it went in. The fix is a row of holes for shelf pins, drilled straight and level, so the shelf can move up or down whenever the gear changes. Learning how to make holes for shelf pins takes a jig, a drill and a steady hand, and the jig does most of the hard work: it spaces the holes, holds the line and keeps the bit square to the panel.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
How to make holes for shelf pins: the quick answer
Clamp a shelf pin jig against the cabinet edge, drill through the jig holes with the bit the jig takes, then move the jig along the edge with the dowel pin to continue the row. The jig sets the spacing and keeps the bit square, so the pins sit level and the shelf does not rock. A 2-in-1 jig also drills the hinge cup hole for the cabinet door, so the same tool covers the shelf pins and the hinges.
Mark the hole line
Start by marking where the row goes on the cabinet side panel. The jig registers against the cabinet edge, so the edge is the reference, not a pencil line down the middle of the panel. Set the jig on the edge, check that it sits flat, and mark the top hole position from the jig itself rather than measuring down from the top of the cabinet.
If the cabinet already has a shelf, check how the shelf sits before drilling: the pins must sit level across the panel, so the holes on the left and the right of the cabinet must line up. Drill the holes on the same side of the panel in the same session, with the jig clamped in the same way each time.
Drill the holes
Fit the bit the jig takes. The TANYO jig (on Amazon) ships with a drill bit in each of the sizes it drills, and the HONTAITUO jig (on Amazon) takes 5mm bits as well as the larger size, so match the bit to the shelf pins you own. Set the drill to a slow, steady speed, hold the jig tight to the edge, and drill each hole through the jig sleeve without forcing the bit.
Drill every hole in the row before moving the jig. The TANYO jig includes a dowel pin for continuous drilling, so the pin drops into the last hole drilled and the jig moves along the edge in line. The HONTAITUO jig drills a full row of 11 holes in a single pass, so a long row needs fewer moves.
Clear the dust from each hole as you go, and check the pin fits before drilling the next row. A pin that sits proud of the panel means the hole needs clearing, not a bigger bit.
Keep the row straight
Straight rows come from the jig, not from the eye. Keep the jig registered against the same cabinet edge for the whole row, and clamp it where the jig offers a clamp: the TANYO and HONTAITUO jigs carry a self-contained clamping function, while the Kreg jigs register against the edge without a clamp. If the jig shifts mid-row, stop, re-seat it on the edge, and pick up from the last hole drilled.
Match the hole size to the pins. The Kreg KMA3232 (on Amazon) drills 5mm holes for European-style cabinets, and the Kreg KMA3225 (on Amazon) drills the larger hole size, so check the pins before choosing the jig. A 5mm pin in a larger hole will not hold the shelf level.
Shelf pin jigs that drill the holes
Each of these jigs handles the drilling step, with the jig setting the spacing and the bit size for the shelf pins.
| # | Product | Office Score | Buy |
|---|---|---|---|
| 1 | TANYO Shelf Pin Jig | 9.7/10 | Buy on Amazon |
| 2 | HONTAITUO 11-Hole Jig | 9.6/10 | Buy on Amazon |
| 3 | Kreg KMA3225 | 9.6/10 | Buy on Amazon |
| 4 | Kreg KMA3232 | 9.6/10 | Buy on Amazon |

TANYO Shelf Pin Jig
A 2-in-1 aluminum shelf pin and hinge jig with 7 holes, 14 removable drill sleeves and a 35mm hinge module, with a self-contained clamp.
Pros
- 2-in-1 shelf pin and hinge jig
- 14 removable drill sleeves
- 35mm hinge module for concealed hinges
- Self-contained clamping function
Cons
- 7 holes per setup, fewer than the 11-hole jig
- The hinge module rides along on shelf-pin-only jobs
- No weight is stated
- No warranty term is stated
Detailed Review
TANYO lists this as a 2-in-1 shelf pin and hinge jig in aluminum, with a 35mm hinge module and 14 removable drill sleeves, 7 for each of the bit sizes it takes, plus a drill bit in each size and a dowel pin for continuous drilling. Double-sided scales mark the hole positions, and the jig clamps to the cabinet edge on its own.
Who it's for: anyone drilling shelf pin holes and hinge cup holes with the same jig. Who should skip it: anyone who only drills shelf pin holes and wants the longest single template.
Its Office Score of 9.7/10 comes from performance 32/35, build 22/25, value 21/25, safety not scored (non-powered gear) and warranty 0/5: 75 of 90 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Holes | 7 |
|---|---|
| Drill sleeves | 14 removable |
| Hinge module | 35mm |
| Material | Aluminum |
These specs mirror the retailer listing as of 14 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. This product does not plug in or run on a battery, so safety is not part of its score. No warranty term, so warranty scores zero. See How We Pick.
Follow the manual. Assemble and use the product as the maker describes, stay under any stated capacity, and read the manual before first use.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

HONTAITUO 11-Hole Jig
An 11-hole 2-in-1 shelf pin and hinge jig that drills a full row of pin holes in a single pass, with a 35mm hinge module and a self-contained clamp.
Pros
- 11 holes drilled in a single pass
- 2-in-1 shelf pin and hinge jig
- 35mm hinge module for concealed hinges
- Self-contained clamping function
Cons
- 1.5 pounds, the heaviest weight stated here
- 11 holes per setup suits long rows; short rows use only part of the template
- No drill bit is stated as included
- No warranty term is stated
Detailed Review
HONTAITUO lists this as a dual-function shelf pin and hinge jig with an 11-hole template that drills a full row of pin holes in a single pass. It takes 5mm drill bits as well as the larger size, fits the most common concealed hinges in the US with a 35mm hinge hole, and clamps to the cabinet on its own. The listing gives the weight as 1.5 pounds.
Who it's for: anyone drilling full rows of shelf pin holes in cabinets. Who should skip it: anyone who only needs a few holes and wants the smallest jig.
Its Office Score of 9.6/10 comes from performance 30/35, build 21/25, value 21/25, safety not scored (non-powered gear) and warranty 0/5: 72 of 90 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Holes | 11 |
|---|---|
| Hinge module | 35mm |
| Weight | 1.5 pounds |
| Clamp | Self-contained |
These specs mirror the retailer listing as of 14 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. This product does not plug in or run on a battery, so safety is not part of its score. No warranty term, so warranty scores zero. See How We Pick.
Follow the manual. Assemble and use the product as the maker describes, stay under any stated capacity, and read the manual before first use.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

Kreg KMA3225
A compact edge-aligned shelf pin jig for drilling accurate shelf pin holes for adjustable shelving in cabinets and furniture.
Pros
- Edge-aligned design for straight, repeatable holes
- Compact jig for fast setup
- Precision guide for evenly spaced holes
- Suits DIY and professional woodworking, per the maker
Cons
- One hole size only
- No hinge function
- No drill bit is stated as included
- No clamping function is stated
Detailed Review
Kreg lists the KMA3225 as a shelf pin jig for drilling accurate shelf pin holes for adjustable shelving in cabinets and furniture. The precision guide keeps the holes evenly spaced, the edge-aligned design registers against cabinet edges for straight, repeatable results, and the compact body sets up fast for DIY and professional woodworking.
Who it's for: anyone who wants a simple edge-aligned jig for shelf pin holes. Who should skip it: anyone who also needs hinge cup holes or a second hole size.
Its Office Score of 9.6/10 comes from performance 29/35, build 21/25, value 20/25, safety not scored (non-powered gear) and warranty 0/5: 70 of 90 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Model | KMA3225 |
|---|---|
| Design | Edge-aligned |
| Color | Blue |
| Setup | Compact, fast setup |
These specs mirror the retailer listing as of 14 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. This product does not plug in or run on a battery, so safety is not part of its score. No warranty term, so warranty scores zero. See How We Pick.
Follow the manual. Assemble and use the product as the maker describes, stay under any stated capacity, and read the manual before first use.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

Kreg KMA3232
A 5mm edge-aligned shelf pin jig for drilling precise shelf pin holes commonly used in European-style cabinets.
Pros
- 5mm holes for European-style cabinets
- Edge-aligned design for straight, repeatable holes
- Precision guide for evenly spaced holes
- Compact jig for fast setup
Cons
- One hole size only
- No hinge function
- No drill bit is stated as included
- No clamping function is stated
Detailed Review
Kreg lists the KMA3232 as a 5mm shelf pin jig for drilling precise shelf pin holes commonly used in European-style cabinets. The precision guide keeps the holes evenly spaced, the edge-aligned design registers against cabinet edges, and the compact body sets up fast for DIY and professional woodworking.
Who it's for: anyone fitting European-style cabinets with 5mm shelf pins. Who should skip it: anyone who needs the larger hole size or hinge cup holes.
Its Office Score of 9.6/10 comes from performance 28/35, build 21/25, value 20/25, safety not scored (non-powered gear) and warranty 0/5: 69 of 90 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Model | KMA3232 |
|---|---|
| Hole size | 5mm |
| Design | Edge-aligned |
| Color | Silver |
These specs mirror the retailer listing as of 14 November 2026; performance figures are stated by the brand.
Safety and Warranty
What this listing states. This product does not plug in or run on a battery, so safety is not part of its score. No warranty term, so warranty scores zero. See How We Pick.
Follow the manual. Assemble and use the product as the maker describes, stay under any stated capacity, and read the manual before first use.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.
As an Amazon Associate I earn from qualifying purchases.
FAQ
What size holes do shelf pins need?
It depends on the pins. The Kreg KMA3232 drills 5mm holes for European-style cabinets, the TANYO and HONTAITUO jigs take 5mm bits as well as the larger size, and the Kreg KMA3225 drills the larger hole size. Check the pins you own before choosing the jig.
Can I drill shelf pin holes without a jig?
A jig is the reliable way: it spaces the holes evenly and keeps the bit square to the panel, while freehand drilling wanders. The Kreg jigs register against the cabinet edge, and the TANYO and HONTAITUO jigs add a clamp to hold the line.
How many holes does a shelf pin jig drill at once?
The TANYO jig drills 7 holes per setup and the HONTAITUO jig drills 11 holes in a single pass, so the HONTAITUO jig covers a longer row before it moves. The Kreg jigs drill hole by hole along the edge.
Do shelf pin jigs also drill hinge holes?
The 2-in-1 jigs do. The TANYO jig carries a 35mm hinge module and the HONTAITUO jig fits the most common concealed hinges in the US with a 35mm hinge hole, while the Kreg jigs drill shelf pin holes only.
What holds the jig still while I drill?
The TANYO and HONTAITUO jigs carry a self-contained clamping function, so the jig clamps to the cabinet edge on its own. The Kreg jigs register against the edge instead, so hold the jig tight to the edge while drilling.
More for your workspace
See the best clamp-on desk shelves, the best desk shelves for home offices, the best wood shelf risers and the small office storage ideas.









