Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›

Home office gear, compared spec by spec.

Amazon Black Friday Week deals
Monitor Mounts, Keyboards and Mice

How to Use a Wireless Speaker: Bluetooth, USB and Aux Setup

How to use a wireless speaker, from Bluetooth pairing to a wired USB or aux connection, with placement and volume tips for a home desk.

How to Use a Wireless Speaker: Bluetooth, USB and Aux Setup

The call starts soon, the laptop sits on the desk, and the sound still comes from the thin speakers built into the screen. A wireless speaker promises fuller sound without another cable snaking across the desk, and learning how to use a wireless speaker takes less fiddling than the box suggests. The steps below cover power, Bluetooth pairing, a wired fallback, and the settings that put the sound where it belongs.

OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

How to use a wireless speaker: the quick answer

Power the speaker on, put it in pairing mode, and pick it from the Bluetooth list on your computer or phone. If the device has no Bluetooth, plug the speaker in with a USB cable or a 3.5 mm aux cable instead. Then set the speaker as the sound output and adjust the volume on the speaker or the device.

Ways to connect a wireless speaker

A wireless speaker usually offers several ways in: Bluetooth for wireless listening, a USB cable that carries power and sound together, a 3.5 mm aux input for a wired signal, and WiFi on speakers built for a home system. The table below shows the connection on each speaker.

Connection How it works Speaker with this connection
Bluetooth 5.0 Pair from the device Bluetooth list Creative Pebble V3, Cyber Acoustics CA-2890BT
Bluetooth 5.3 Pair from the device Bluetooth list Creative Pebble Pro
Bluetooth 6.0 Pair from the device Bluetooth list Monster S220
USB-C One cable for power and sound Creative Pebble V3, Creative Pebble Pro, Tylubio soundbar
3.5 mm aux Wired input from a headphone jack Creative Pebble V3, Creative Pebble Pro, Monster S220
WiFi and line in Stream over WiFi or plug in a turntable Sonos Era 100 SL

Step 1: Power the speaker

Start with power, since a speaker that is off or flat will not pair. The Monster S220 (on Amazon) lists a 2000mAh built-in battery, while other speakers draw power from the USB cable that also carries the sound. The Creative Pebble V3 takes power from a USB-C cable, and its gain switch needs a 10W USB-C or USB-A port for amplified sound. The Creative Pebble Pro runs from USB-C too, and the maker states it reaches its full 30W RMS and 60W peak power with a 30W USB PD adapter. On the Tylubio soundbar (on Amazon), a long press of the knob for 3 seconds powers it on or off. Plug the speaker in first, then press the power button.

Step 2: Pair over Bluetooth

Put the speaker in pairing mode first. On the Creative Pebble V3, press the Bluetooth button, then pick the speaker from the Bluetooth list on the phone or computer. On the Tylubio soundbar, a single click of the knob switches between USB and Bluetooth modes, and a quadruple click resets Bluetooth when a pairing will not stick. The Monster S220 pairs over Bluetooth 6.0, which the maker lists with less than 15ms latency, so sound stays in step with video. Once the device shows the speaker as connected, play a short clip to check the sound comes from the speaker.

Step 3: Connect by cable when Bluetooth will not do

A cable is the fallback when pairing fails or the device has no Bluetooth. The Creative Pebble V3 runs from a single USB-C cable, and the box includes a USB-C to USB-A converter for older computers with a USB-A port. The Cyber Acoustics CA-2890BT (on Amazon) also includes a USB A to USB C converter, and its 5ft cable reaches from the desk to the computer. A 3.5 mm aux cable plugs into the aux-in jack on the Pebble V3, the Pebble Pro, or the Monster S220, and the jack takes a wired signal from any device with a headphone output. Keep the cable run short so it stays out of the way.

Step 4: Set the speaker as the output and set the volume

Once the speaker is paired or plugged in, open the sound settings on the computer or phone and set the speaker as the output device. If sound still comes from the device itself, switch the output over and play a clip again. Set the volume on the speaker first, then fine-tune it on the device, and use the Clear Dialog processing on the Pebble V3 or Pebble Pro when spoken words in a film or a call are hard to follow. The Cyber Acoustics CA-2890BT has a mic mute button with an LED indicator for hands-free calls, so mute from the speaker when the call needs quiet.

Where to put the speaker

Place the speaker where its drivers point at your ears. The Creative Pebble V3 and Pebble Pro use 45° elevated drivers that angle the sound up toward the listener, so set them in front of you rather than behind the monitor. The Tylubio soundbar measures 15.7 x 2.7 x 2.5 inches and sits under the monitor, and the Monster S220 measures 16.5 x 2.4 x 2.4 inches and slides under the monitor too. The Sonos Era 100 SL (on Amazon) measures 4.72 x 5.19 x 7.22 inches, and a pair of them can play in stereo when two are set up together. Leave the speaker clear of walls and clutter so the sound has room to spread.

FAQ

Can a wireless speaker connect to a computer without Bluetooth?

Yes. Plug it in with a USB cable or a 3.5 mm aux cable: the Creative Pebble V3 runs from a single USB-C cable, and its 3.5 mm aux-in jack takes a wired signal from a computer with a headphone output. The Tylubio soundbar also connects over USB and Type-C with no adapter needed.

Why does my wireless speaker keep dropping the connection?

Check power first: the Creative Pebble Pro needs USB-C power, and it reaches its full 30W RMS and 60W peak power only with a 30W USB PD adapter. Then reset the pairing: on the Tylubio soundbar, a quadruple click of the knob resets Bluetooth. If the speaker still will not pair, switch to a USB cable or a 3.5 mm aux cable instead.

Can I use a wireless speaker for video calls?

Yes, if the speaker suits calls. The Cyber Acoustics CA-2890BT is built for calls and music, with a speakerphone and a mic mute button, and it switches between USB and Bluetooth so the computer and the phone can both stay connected. The Creative Pebble Pro also takes a headset or microphone through its headset or microphone port, which turns the speakers into a communications tool for calls.

Can a wireless speaker play music from a turntable?

Yes, with a speaker that has a line input. The Sonos Era 100 SL connects a turntable and more with line in, and it streams over WiFi or pairs over Bluetooth as well. Plug the turntable into the line input, pick the speaker as the output, and play a record.

More for your workspace

See the computer speaker setup guide, the best desktop Bluetooth speaker picks, the best high quality Bluetooth speakers, and the best wireless speaker for PC and phone.