Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›

Home office gear, compared spec by spec.

Amazon Black Friday Week deals
Keyboards and Keyboard Trays

Keyboard Stabilizer Types: Which Kind Should You Buy

Screw-in, snap-in and plate-mount keyboard stabilizers explained, with wire sizes for 2u, 6.25u and 7u keys, PCB thickness and kit contents.

Keyboard Stabilizer Types: Which Kind Should You Buy

A spacebar that rattles when you tap its edge is the moment most people meet keyboard stabilizer types: the small parts under wide keys that keep each key level as it travels down. A stabilizer links both ends of a wide key with a wire, so the key presses evenly instead of tilting. This guide explains the main types, screw-in, snap-in and plate-mount, and the wire sizes and PCB thickness figures that decide which kit fits a keyboard.

OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

The quick answer

Every wide key on a mechanical keyboard sits on a stabilizer, and the type that fits depends on how the keyboard is built. Screw-in PCB-mount stabilizers, such as the DUROCK V3, the Zkeebs Knight V4 and the MELETRIX WS V3.1, fasten to the PCB with screws. Snap-in PCB-mount stabilizers, such as the MELETRIX WS, clip into the PCB. Plate-mount stabilizers, such as the YMDK Costar set and the ZugGear DUROCK plate mount (on Amazon), clip into the plate instead. Wire sizes follow the key: 2u wires suit enter, backspace or shift, while 6.25u and 7u wires suit spacebars.

Keyboard stabilizer types at a glance

Type Mount Wire sizes Notes
Screw-in PCB mount PCB with screws 2u, 6.25u, 7u DUROCK V3, Zkeebs Knight V4, MELETRIX WS V3.1
Snap-in PCB mount PCB, clips in 2u, 6.25u, 7u MELETRIX WS; 1.2mm or 1.6mm PCBs; 87% and 108% keyboards
Plate-mount Costar Plate 2u, 6.25u YMDK Costar; Kit 1 for 60 and 87, Kit 2 for 96 and 104
Plate-mount DUROCK Plate 2u, 6.25u, 7u ZugGear DUROCK plate mount; 60 and 87 keyboard kit
Stabilizer films Between stabilizer and PCB Not stated RunJRX Teflon pads, 20 pcs, 3M adhesive backing

Step 1: Match the mount to the keyboard

Screw-in stabilizers fasten to the PCB with screws and washers. The DUROCK V3 is for screw-in keyboards only, and the kit includes washers, screws and a Soulmate Tuning Kit. The Zkeebs Knight V4 is also a PCB screw-in set, with screws, washers and stabilizer shims included. Snap-in stabilizers clip into the PCB without screws: the MELETRIX WS is a PCB-mount snap-in set for 1.2mm or 1.6mm PCBs. Plate-mount stabilizers clip into the plate: the YMDK Costar set is plate-mounted, and the ZugGear DUROCK set is a plate-mount set for MX-compatible plates. Check the keyboard first: a PCB without screw holes takes snap-in stabilizers, a PCB with screw holes takes screw-in stabilizers, and a plate build takes plate-mount stabilizers. If the keyboard itself is still undecided, see the best mechanical keyboards guide.

Step 2: Match the PCB thickness

Stabilizers are sized for the PCB thickness, and the common figures are 1.2mm and 1.6mm. The DUROCK V3 is designed for 1.6mm PCB keyboards and fits most 1.2mm to 1.6mm PCBs with the included washers. The Zkeebs Knight V4 fits 1.2mm PCBs with shims and 1.6mm PCBs. The MELETRIX WS comes in 1.2mm or 1.6mm versions, and the MELETRIX WS V3.1 also comes in 1.2mm or 1.6mm. Measure the PCB thickness before ordering, since a stabilizer sized for one thickness will not sit right on the other. Stabilizers sit beside the switches, so see the keyboard switches types guide for the switch side of the build.

Step 3: Pick the wire sizes for the layout

Wire size follows the key size, and the sizes in these kits are 2u, 6.25u and 7u. Use 2u wires for enter, backspace or shift, and 6.25u or 7u wires for the spacebar. Kit contents show the split: the DUROCK 80% kit holds 2ux4, 6.25ux1 and 7u wirex1, while the DUROCK 100% kit holds 2ux7, 6.25ux1 and 7u wirex1. The Zkeebs 80% TKL kit holds 10 stems, 10 housings, 4 2U wire, 1 6.25U wire and 1 7U wire. The YMDK Costar Kit 1 holds 1×6.25 and 4x2u for 60 and 87 keyboards, and Kit 2 holds 1×6.25 and 7x2u for 96 and 104 keyboards. The jojofuny set holds 1 set of 6.25u, 7 sets of 2u, 1 7u steel wire and 18 brass sheets. The YMDK 6.25u wire measures 4.21 inch and the 2u wire measures 1.18 inch.

Step 4: Lube, films and rattle

Stabilizers rattle when the wire moves loosely in the housing, and makers quiet them with lube, films or tighter parts. The MELETRIX WS V3.1 comes pre-lubed, and its housing design keeps wires from popping out. The DUROCK V3 includes a Soulmate Tuning Kit with washers, and its pre-clipped stem and smaller wire gap aim to cut wobble and noise. The Zkeebs Knight V4 uses an injection-treated stem and housing to cut rattling sounds where the stem meets the housing and where the wires meet the stem. RunJRX Teflon films (on Amazon) sit between the stabilizer and the PCB as a buffer, with a 3M adhesive backing, in a set of 20 pcs. The MELETRIX WS uses a POM housing and a PC stem for stability. For lube options, see the best lube for keyboard stabilizers guide.

FAQ

What does a keyboard stabilizer do?

A stabilizer keeps a wide key level as it travels down, so the key presses evenly from any point. It sits under keys such as the spacebar, enter, backspace and shift, with a wire that links both sides of the key.

Are screw-in stabilizers better than snap-in stabilizers?

Screw-in stabilizers fasten to the PCB with screws and washers, as on the DUROCK V3 and the Zkeebs Knight V4, so they stay put once installed. Snap-in stabilizers clip into the PCB, as on the MELETRIX WS, and suit boards without screw holes. Pick the mount that matches the PCB.

What size stabilizer wire do I need?

Match the wire to the key: 2u wires suit enter, backspace or shift, while 6.25u and 7u wires suit spacebars. The DUROCK 80% kit includes 2ux4, 6.25ux1 and 7u wirex1, and the 100% kit includes 2ux7, 6.25ux1 and 7u wirex1.

Do stabilizers fit 1.2mm and 1.6mm PCBs?

The DUROCK V3 is designed for 1.6mm PCBs and fits most 1.2mm to 1.6mm PCBs with the included washers. The Zkeebs Knight V4 fits 1.2mm with shims and 1.6mm, and the MELETRIX WS comes in 1.2mm or 1.6mm versions.

What are stabilizer films for?

Stabilizer films sit between the stabilizer and the PCB as a buffer. The RunJRX set includes 20 Teflon pads with a 3M adhesive backing, and only applies to PCB satellite switches.

Can I use plate-mount stabilizers on a PCB-mount keyboard?

No. Plate-mount stabilizers such as the YMDK Costar set and the ZugGear DUROCK plate mount fit MX-compatible plates, while PCB-mount stabilizers such as the DUROCK V3 fasten to the PCB. The jojofuny set mounts on a compatible keyboard PCB, not a positioning plate.

More for your workspace

See every keyboards guide and all computer peripherals guides. Also see the best mechanical keyboards, the keyboard switches types and the mechanical keyboard types guides.