The call starts, you push the chair back and stand at the desk, and by the time the meeting ends your feet have found the hard floor and stayed there. A mat under the standing spot puts a mat between your feet and the hard floor, and a mat cut to fit the space does it without curling at the edges or sliding out from under the desk. This guide explains custom size anti fatigue mats: how to measure the standing area, how to match the width and depth to the desk, and how to check thickness, edges and weight before you order.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
The quick answer
A custom size anti fatigue mat is a mat made to the width and depth of the standing area in front of a desk, instead of a fixed size that leaves gaps or overhang. Measure the floor where you stand, from the desk front to where your heels land and across the width you use, then order a mat that covers that patch. The Fellowes mat (on Amazon) in this guide measures 36 by 24 inches, with a thickness of 0.75 inches, so it works as a reference size for a standing spot at a desk: if the area you measured is larger, order a mat that covers the full area.
Custom size anti fatigue mats: what to measure
| Measurement | Fellowes mat |
|---|---|
| Width | 36 in |
| Depth | 24 in |
| Thickness | 0.75 in |
| Weight | 4.58 lb |
| Warranty | 5 Year Limited |
| Material | Not stated |
The listing gives the size as 36 by 24 inches and the thickness as 0.75 inches, and it gives the weight as 4.58 lb. The warranty is a 5 Year Limited Warranty. The material is Not stated in the listing. Use these figures as the reference when you compare a custom size: a wider mat covers more of the standing area, and a thicker mat raises the standing surface higher off the floor.
Measure the standing area
Start with the floor, not the catalog. Stand at the desk the way you stand when you work, then look down and note where your feet land. Mark the floor at the outer edges of that stance with tape, then measure the width across the marks and the depth from the desk front to the back edge of the stance. Write the width and depth down before you shop, and keep the tape on the floor while you compare sizes, so the figures stay visible. A mat that matches those marks covers the full stance; a mat that falls short leaves part of each foot on the bare floor.
Match the width to the desk
The width of the mat should cover the standing spot across the front of the desk, so your feet stay on the mat when you shift from the keyboard to the far side of the desk. A mat that is narrower than the standing area forces a choice between standing on the mat and standing where the work is. Check the desk width against the mat width, and leave room at the sides for the chair to roll in when you sit down. The standing desk dimensions guide covers desk widths, and the best standing desks for working from home guide shows how wide a standing setup runs.
Check the depth for your stance
Depth matters as much as width, because the mat has to sit under the whole foot, heel to toe, through the full range of the stance. A shallow mat leaves the heels on the bare floor when you step back, and a deep mat runs past the chair and into the walkway. Stand at the desk, step back to the far edge of the stance, and check that the depth you measured covers the feet at that point. The Fellowes mat has a depth of 24 inches, so compare the depth you measured with that figure: a deeper stance calls for a deeper mat.
Check thickness, edges and weight
Thickness sets how far the mat lifts the feet off the floor, and the Fellowes mat is 0.75 inches thick. Beveled edges slope down to the floor, and the listing describes them as a way to help avoid tripping hazards where the mat meets the floor. Weight sets how the mat behaves when you move it: the Fellowes mat weighs 4.58 lb, so it lifts off the floor by hand when the desk layout changes. Check the thickness and the edges on the mat you order, and check that the weight suits the way you plan to move it.
Where a custom size mat fits
The listing for the Fellowes mat describes it as suitable for the office, the kitchen and the laundry room, and for any place where standing lasts a while. That range matters for a custom size, because the standing area in a kitchen differs from the standing area at a desk, and each room calls for its own width and depth. Measure each room the same way: mark the stance, measure the width and depth, and order the size that covers it. The what is anti fatigue matting guide explains the mat type, and the best anti fatigue mats for home office guide compares mats made for desk use. The best thin anti fatigue mats for standing desks guide covers thinner mats for standing desks.
FAQ
What size is the Fellowes anti-fatigue mat?
The Fellowes mat measures 36 by 24 inches, with a thickness of 0.75 inches. It weighs 4.58 lb, and the warranty is a 5 Year Limited Warranty. Use those figures as the reference size when you measure a custom size.
How do I measure for a custom size anti fatigue mat?
Stand at the desk, mark the outer edges of the stance with tape, and measure the width across the marks and the depth from the desk front to the back edge of the stance. Order a mat that covers the full marked area, and keep the tape on the floor while you compare sizes.
Can I use an anti-fatigue mat in the kitchen?
Yes. The listing for the Fellowes mat describes it as suitable for the office, the kitchen and the laundry room, and for any place where standing lasts a while. Measure the standing area in the kitchen the same way you measure it at the desk.
What warranty does the Fellowes mat carry?
The listing states a 5 Year Limited Warranty. Check the warranty terms on the mat you order, since terms differ by maker.
More for your workspace
See the best anti fatigue mats, the best anti fatigue mats for home office, the best thin anti fatigue mats for standing desks and the standing desk setup guide, and every desks guide.





