The converter arrives in a box, the desk is already crowded, and the monitor has to go somewhere that works for sitting and standing. Standing desk setup is the order of work: set the desk height, place the monitor and keyboard, then lay out the mat and the rest of the desk. This guide walks through each step, with figures from the JYLH JOYSEEKER converter (on Amazon) listing named here.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
Standing desk setup: the quick answer
Set the height so the forearms rest level when the elbows bend, place the monitor at eye level about an arm’s length away, and put the keyboard and mouse on the tray below the desktop. The JYLH JOYSEEKER converter adjusts from 4.7 in to 16.1 in on a gas spring, with a 28 in by 17.7 in desktop and a 26.8 in by 10.2 in keyboard tray. Work through the steps below in order: height, monitor, keyboard, then the mat and the rest of the desk.
Step 1: Set the desk height
Height comes first, because the monitor and keyboard follow it. The JYLH JOYSEEKER converter adjusts from 4.7 in to 16.1 in with a smooth gas spring, so the desktop rises from a low sitting height to a standing height. Sit with the feet flat and the arms hanging, then bend the elbows until the forearms rest level: the keyboard should sit at that height. Stand and repeat the same check on the feet: the desktop should sit at about elbow height. If the forearms still angle down at the top of the range, the desk underneath sits too low for standing work.
Step 2: Place the monitor
The monitor sits on the desktop, and the JYLH JOYSEEKER desktop measures 28 in by 17.7 in, with a device slot and a cup holder built in. Set the screen so the top sits at or slightly below eye level, and keep the screen about an arm’s length away, so the head stays level while reading. The desktop supports up to 17.6 lbs, so check the monitor and anything else on the desktop against that figure before loading the surface. A monitor stand raises a low screen without changing the desk.
Step 3: Place the keyboard and mouse
The keyboard and mouse belong on the tray, below the desktop. The JYLH JOYSEEKER keyboard tray measures 26.8 in by 10.2 in with curved edges, and it holds up to 5 lbs. Keep the keyboard at the height where the forearms rest level, with the mouse beside it on the same tray, so the wrists stay straight while typing. If the tray runs short, move the mouse to the desktop and keep the keyboard on the tray.
Step 4: Lay out the mat and the rest of the desk
The converter needs a steady base. The JYLH JOYSEEKER listing states a triple clamp base with anti-slip pads, and a 10 in by 9.8 in base that takes up little space. The converter itself weighs 27.5 lbs, so set it down and leave it in place. Keep the cup holder and the device slot clear for the cup and the phone, and post notes on the magnetic panel with the 6 colorful magnets. Run cables down the back of the desk so they do not catch when the converter rises, and leave slack for the full range from 4.7 in to 16.1 in. The mat goes under the desk where the feet land for standing work.
Cables and clutter
Cables decide whether the converter moves freely. Run the monitor and keyboard cables down the back of the desk, and leave slack for the full range from 4.7 in to 16.1 in, so nothing pulls tight when the desktop rises. Keep the cup holder for the cup and the device slot for the phone, so drinks and devices stay off the keyboard tray. Post notes and reminders on the magnetic panel with the 6 colorful magnets, and keep the desktop clear of anything the converter could knock over when it moves.
What the converter holds
Weight limits decide what goes on the desktop and the tray. The JYLH JOYSEEKER desktop supports up to 17.6 lbs and the keyboard tray holds up to 5 lbs, while the converter itself weighs 27.5 lbs. Check the weight of the monitor, the keyboard and anything else on the desktop against the 17.6 lbs the desktop supports, and keep heavy items off the keyboard tray. The listing states a premium MDF board desktop and a reinforced clamp with anti-slip pads, which the maker describes as holding the converter steady while guarding the desk from scratches.
Sitting and standing through the day
A converter earns its place by switching, not by staying up. Lower it for sitting work and raise it for standing work, and change position through the day rather than staying in one position all day. Set the height again after each switch: the sitting height and the standing height are not the same. Keep the chair pushed in while standing, and the mat under the desk for standing work, so the floor stays clear and the desk stays usable from either position.
FAQ
How high should a standing desk converter go?
High enough for the forearms to rest level while standing. The JYLH JOYSEEKER converter adjusts from 4.7 in to 16.1 in on a gas spring. Set the height so the keyboard sits at elbow height while standing, and lower it to the sitting height when the chair is in use.
How much weight can the converter hold?
The JYLH JOYSEEKER desktop supports up to 17.6 lbs and the keyboard tray holds up to 5 lbs. The converter itself weighs 27.5 lbs. Check the monitor and keyboard against those figures before loading the desktop and the tray.
How big is the converter desktop?
The JYLH JOYSEEKER desktop measures 28 in by 17.7 in, and the keyboard tray measures 26.8 in by 10.2 in. The base measures 10 in by 9.8 in, so the converter fits a narrow desk. Measure the desk before ordering, and check the listing for the model you buy.
Does the converter need assembly?
The JYLH JOYSEEKER listing states a clamp-on design with a detailed installation manual and video, and states assembly is completed within minutes. The listing also states tech support is provided for questions.
More for your workspace
See the best standing desks for working from home, the best monitor stands, the best keyboard trays and the best under-desk footrests.





