A dual monitor setup puts a pair of screens side by side on a desk, both driven by a computer, so work spreads across a wide view instead of crowding onto a single display. The setup needs a pair of monitors, a way to hold them, and a video connection for each screen. This guide walks through the checks and steps in order: screen size, weight and VESA patterns, desk thickness and mount type, connection, then height, tilt and layout.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
Dual monitor setup: the quick answer
Start with the monitors: check the screen size, the weight and the VESA hole pattern on the back of each screen. Match those figures to a dual arm that lists a size range and a weight range covering both screens. Check the desk: a C-clamp mount grips the edge, while a grommet mount needs a hole through the desktop. Connect each screen to the computer, then set the height so the top of each screen sits near eye level, tilt each screen to cut glare, and line the screens up so the edges meet without a gap.
What the arms in this guide cover
The listings below show the size and weight ranges dual arms state. Use the table to see how wide the ranges run, then match your own screens to an arm that covers them.
| Arm | Screen size | Weight per arm |
|---|---|---|
| ErGear EGDS15B | 17 to 33 in | 4.4 to 22 lbs |
| MOUNTUP Freelift | 22 to 32 in | 4.4 to 19.8 lbs |
| Acer AMS002 | 17 to 32 in | 4.4 to 19.8 lbs |
| Amazon Basics DS-MADDBE | 15 to 27 in | 4.4 to 15.4 lbs |
| HUANUO FlowLift Pro | 13 to 27 in | 4.4 to 15.4 lbs |
| DUMOS dual mount | 13 to 32 in | 4.4 to 17.6 lbs |
| HUANUO HNDS18 | 17 to 32 in | Up to 22 lbs |
Every arm here lists VESA patterns of 75×75 mm or 100×100 mm, and every arm here lists a weight range that starts at 4.4 lbs. The smallest screens in these listings start at 13 in, and the largest reach 33 in.
Step 1: Check the screens
Check the diagonal size and the weight of each screen, then check the back for a square of mounting holes spaced 75×75 mm or 100×100 mm apart. A screen with no VESA holes cannot bolt to an arm, so it needs a stand that holds it by the base instead. The MOUNTUP listing covers flat or curved monitors from 22 in to 32 in, and the HUANUO HNDS18 listing covers flat or curved monitors from 17 in to 32 in. Keep each screen inside the arm’s stated weight limit: the limits here run from 15.4 lbs to 22 lbs per arm, so a heavy screen needs an arm that lists a limit above the screen’s weight. A monitor stand suits a screen with no VESA holes, while a monitor arm suits a screen that has them.
Step 2: Check the desk
Desk thickness decides the mount. C-clamp mounts in these listings fit desks from 0.39 in to 4 in thick, and grommet mounts fit desks from 0.39 in to 2.76 in thick, with a hole from 0.39 in to 2.36 in across. The Acer listing also gives a grommet hole above 10 mm and a desk thickness from 0.59 in to 3.15 in. The ErGear listing recommends a wood desk, and the HUANUO FlowLift Pro listing recommends wood desks from 0.59 in to 3.54 in thick. Check the underside of the desk for beams or panels that block a clamp, and check the edge: an irregular edge needs care with a clamp mount, so a grommet mount may suit a desk with a shaped edge better.
Step 3: Mount the arm and the screens
Fix the base to the desk first: tighten the C-clamp on the edge or drop the grommet bolt through the hole. The HUANUO HNDS18 listing states setup takes 10 minutes with the included tools and instructions. Attach a VESA plate to each screen, hang each screen on its arm, and tighten the knobs. Set the tension: gas spring arms use a tension screw, and heavier screens need more tension. The Amazon Basics listing gives turn counts for its arm: 7 turns for 13.2 lbs, 12 turns for 11 lbs, 16 turns for 8.8 lbs, and 19 turns for 5.5 lbs. The ErGear, MOUNTUP and Acer listings state 20,000 cycles or more, and the DUMOS listing states 25,000 cycles. Check that each screen stays put at the height you set before moving on to cables.
Step 4: Connect the screens
Each screen needs its own video connection to the computer. A desktop with a pair of video outputs connects directly, while a laptop with a single video output needs a dock or a hub to drive a pair of screens. The site’s docking station guides cover docks for dual monitors and a laptop, and a docking station for dual monitors and a laptop is the route when the laptop has a single video output. Route the cables through the arm: the MOUNTUP listing hides cables inside the arms, the Acer listing uses hidden cable clips, and the Amazon Basics listing uses built-in cable management. A cable guide for dual monitors helps keep the runs tidy.
Step 5: Set height, tilt and layout
Raise the screens so the top of each screen sits near eye level. Arms in these listings rise from 16.9 in to 18.25 in above the desk, and extend from 17.5 in to 21.25 in toward you. Tilt runs from -90 degrees to +90 degrees across the listings, swivel runs to 90 degrees or 180 degrees, and rotation runs to 360 degrees for portrait mode. Line the screens up edge to edge, with the main screen straight ahead and the second screen angled in. For a laptop plus a screen, a laptop stand for dual monitor use lifts the laptop to screen height. Common layouts:
- Side by side: a pair of screens in landscape, edges touching, for work spread across a wide view.
- Main and side: a main screen straight ahead with a second screen angled in for reference material.
- One vertical: a second screen rotated to portrait mode for long documents or code.
FAQ
What size monitors fit a dual monitor arm?
Arms in these listings cover screens from 13 in to 33 in, so check your own screen size against the arm’s stated range. The ErGear arm (on Amazon) covers 17 in to 33 in, while the HUANUO FlowLift Pro covers 13 in to 27 in.
How much weight can each arm hold?
Each arm in these listings holds from 4.4 lbs up to 15.4 lbs, 17.6 lbs, 19.8 lbs or 22 lbs, depending on the arm. Weigh each screen and match it to an arm that lists a limit above the screen’s weight.
Do my monitors need VESA holes?
Yes, for an arm mount. Every arm here fits VESA patterns of 75×75 mm or 100×100 mm, so check the back of each screen for that hole pattern. A screen with no VESA holes needs a stand that holds it by the base instead.
Can I use a dual monitor setup with a laptop?
Yes. A laptop with a single video output needs a dock or a hub to drive a pair of screens, and a laptop stand lifts the laptop screen to the height of the external screen. The site’s docking station guides cover docks for dual monitors and a laptop.
What desk thickness works with a dual monitor arm?
C-clamp mounts in these listings fit desks from 0.39 in to 4 in thick, and grommet mounts fit desks from 0.39 in to 2.76 in thick. Measure the desk edge before ordering, and check the underside for beams or panels that block a clamp.
More for your workspace
See every monitor arms and stands guide and all computer peripherals guides.
More picks: monitor arms, dual monitor stands for home office, L-shaped desks for dual monitor setups.





