Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›

Home office gear, compared spec by spec.

Amazon Black Friday Week deals
Monitor Arms and Stands

Dual Monitor Arm Setup: Mounting Screens Side by Side

A dual monitor arm setup lifts both screens off the desk: check fit, mount the base, hang the screens and set height, tilt and swivel.

Dual Monitor Arm Setup: Mounting Screens Side by Side

A dual monitor arm setup lifts screens off the desk and holds them at eye level on arms that clamp to the rear edge or bolt through a grommet hole. Each screen hangs from its own arm on a VESA plate, so the screens can tilt, swivel and rotate into place while the desktop stays clear underneath. The steps below walk through checking fit, mounting the base, hanging the screens and routing the cables.

OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

The quick answer

Check the fit first: each monitor needs a screen size and a weight inside the range the arm lists, plus VESA holes spaced 75×75 or 100×100 mm on the back. Then check the desk: the clamp or grommet base needs a thickness inside the range the maker lists, and the spot under the desk needs room for the clamp. Mount the base, attach a VESA plate to each screen, hang the screens on the arms, and set height, tilt and swivel until the tops of the screens sit near eye level. Route the cables through the arms last, and move each arm through its full range to make sure nothing pulls tight.

Dual monitor arm setup: check fit first

Every dual monitor arm lists three fit conditions, and all three have to hold at the same time: screen size, weight per arm and VESA pattern. The listings below cover screens from 13 to 33 inches and loads from 4.4 to 22 lbs per arm, so match your own screens against the row that fits them. Desk thickness matters just as much: a clamp that fits a 0.39 to 2.56 inch desk will not grip a thicker top, and a grommet base needs a hole in the right size range.

Listing Screen size Weight per arm VESA pattern Desk thickness
ErGear EGDS15B 17 to 33 in 4.4 to 22 lbs 75×75, 100×100 Clamp 0.39 to 2.56 in; grommet 0.39 to 2.17 in
MOUNTUP Freelift 22 to 32 in 4.4 to 19.8 lbs 75×75, 100×100 0.39 to 2.76 in
Acer AMS002 17 to 32 in 4.4 to 19.8 lbs 75×75, 100×100 0.59 to 3.15 in
Amazon Basics DS-MADDBE 15 to 27 in 4.4 to 15.4 lbs 75×75, 100×100 0.39 to 4 in
HUANUO FlowLift Pro 13 to 27 in 4.4 to 15.4 lbs 75×75, 100×100 0.59 to 3.54 in, wood desks
DUMOS 13 to 32 in 4.4 to 17.6 lbs 75×75, 100×100 0.39 to 3.15 in
HUANUO HNDS18 17 to 32 in Up to 22 lbs 75×75, 100×100 Clamp 0.39 to 2.56 in; grommet 0.39 to 2.17 in

Measure the desk before you order. ErGear lists a wooden table with the underside clear of beams or panels, and Acer states its mount is not suitable for glass or plastic surfaces. For a grommet base, check the hole too: MOUNTUP lists a bolt-through hole of 0.39 to 2.36 inches, Amazon Basics lists a grommet hole diameter of 1.5 to 2.36 inches, and Acer lists a hole wider than 10 mm. A hole outside the listed range leaves the base loose or unable to pass through.

Step 1: Mount the base to the desk

Pick the mounting style that fits the desk. A C-clamp grips the rear edge and needs no hole, while a grommet base bolts through a hole in the desktop. ErGear and HUANUO list a C-clamp range of 0.39 to 2.56 inches and a grommet range of 0.39 to 2.17 inches; MOUNTUP lists 0.39 to 2.76 inches for both styles. Set the base where the arms can reach both screen positions, tighten the clamp or the grommet bolt until the base does not shift when you push it, and check that the underside is clear of beams or panels before you hang any weight on it. HUANUO states its HNDS18 mount sets up in 10 minutes with the included tools and instructions.

Step 2: Attach the VESA plates and hang the screens

Take the screens off their factory stands and bolt a VESA plate to the holes on the back of each monitor, matching the 75×75 or 100×100 mm spacing the listing states. A monitor mount screw size guide helps when the plate screws do not match the holes. Hang each plate on its arm and tighten the knobs until the plate sits flat: HUANUO lists tightening knobs on its HNDS18 mount, and the FlowLift Pro lists a tool-free plate that snaps into place with a click. Keep a hand on each screen until the plate is seated, since an arm with no load swings freely.

Step 3: Set height, tilt and swivel

Raise the arms until the tops of the screens sit near eye level, then set the tilt and swivel for each screen. The listings state height adjustment up to 17.5 inches on the ErGear and HUANUO HNDS18 mounts, 16.9 inches on the MOUNTUP mount (on Amazon) and 18.1 inches on the Acer mount (on Amazon), with extension up to 17.5 inches on the ErGear mount (on Amazon), 19.5 inches on the MOUNTUP mount, 20.5 inches on the Amazon Basics mount (on Amazon) and 21.25 inches on the Acer mount. Tilt runs from -35° to +90° on some mounts and -90° to +85° on the Amazon Basics mount, swivel runs to 180° on the MOUNTUP and DUMOS mounts (on Amazon), and every listing here states 360° rotation for portrait or landscape use. If a screen sinks or rises on its own, adjust the tension: Amazon Basics lists its arms pre-set for 15.4 lb monitors, with 7 turns for 13.2 lbs, 12 turns for 11 lbs, 16 turns for 8.8 lbs and 19 turns for 5.5 lbs, turning clockwise to match a lighter screen. Acer lists a tension screw to turn up for heavier monitors and down for lighter ones. ErGear and MOUNTUP state 20,000 cycles for the arm, and DUMOS states 25,000 cycles.

Step 4: Route the cables and check the range

Run each cable along its arm and through the cable clips or channels the mount provides, leaving enough slack for the arm to move. MOUNTUP lists cable management that hides wires inside the arms, Amazon Basics lists integrated cable management, and Acer lists hidden cable clips. Plug everything in, then move each arm through its full range of height, tilt and swivel and watch the cables: if a cable pulls tight at full extension, reroute it with more slack before you settle in. A cable management guide for monitor arms shows clips and channels that keep the run tidy.

FAQ

What size monitors fit a dual monitor arm?

It depends on the listing: the mounts here state ranges from 13 to 27 inches up to 17 to 33 inches, and every one of them needs VESA holes spaced 75×75 or 100×100 mm. Measure the screen size as the maker states it, and check the weight too, since a screen inside the size range can still sit outside the weight range.

How much weight can each arm hold?

The listings here state 4.4 to 15.4 lbs per arm on the smaller mounts and 4.4 to 22 lbs per arm on the ErGear and HUANUO HNDS18 mounts, with the DUMOS mount at 4.4 to 17.6 lbs. Check the weight the maker lists for each monitor, and keep each screen inside the range for its arm. A screen below the minimum weight can rise on a gas spring arm, so set the tension to match.

Will a dual monitor arm fit my desk?

Check the thickness first: the mounts here list clamp ranges from 0.39 to 2.56 inches up to 0.39 to 4 inches, and grommet ranges from 0.39 to 2.17 inches up to 0.39 to 2.76 inches. The desk also needs a clear spot for the base, and ErGear lists a wooden table while Acer states its mount is not suitable for glass or plastic surfaces. For a grommet base, measure the hole as well: the listings state holes from 0.39 to 2.36 inches and a diameter of 1.5 to 2.36 inches.

Can I turn one monitor to portrait?

Yes, if the mount states 360° rotation: every listing here lists 360° rotation, so either screen can turn from landscape to portrait. Set the tilt and swivel after the rotation, since the screen sits higher and closer to the other monitor in portrait, and check the cables again at the new angle.

More for your workspace

See the best monitor arms, the best VESA monitor stands, the best standing desks for working from home and every Monitor Mounts, Keyboards and Mice guide.