Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›

Home office gear, compared spec by spec.

Amazon Black Friday Week deals
Office Chairs and Seating

How to Adjust a Office Chair Step by Step

Adjusting an office chair means setting the seat height, backrest angle, armrests, lumbar support and headrest in order, so the chair fits the person sitting in it.

How to Adjust a Office Chair Step by Step

A chair that sinks by midday, a backrest that leans too far, and armrests that leave your shoulders hanging all make a workday harder than it needs to be, and how to adjust a office chair comes down to setting the seat, the backrest, the armrests and the headrest in order, one lever at a time. Start with seat height, then the backrest angle, then the arms, and finish with the headrest and lumbar support.

OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

The quick answer

Sit in the chair with your feet flat on the floor and your thighs roughly level, then raise or lower the seat until your knees sit at or slightly below hip height. Lock the backrest upright for typing, set the armrests so your forearms rest level, and move the lumbar support and headrest until they meet your lower back and head without pushing either forward. The sections below take each control in turn, with the figures one listing states as a guide.

How to adjust a office chair: seat height first

The seat height lever is the control to reach for first, and it sits under the seat on most chairs. Lift the lever while standing, then sit and let the seat settle until your feet rest flat on the floor and your thighs sit roughly level. GABRYLLY lists a seat height of 19.2 to 23.7 in on its high-back chair, a range the listing pairs with users from 5’5″ to 6’3″. If your feet dangle, lower the seat; if your knees sit above your hips, raise it. A footrest helps when the desk height cannot change and the chair must sit high to meet it.

Set the backrest angle

The backrest on most chairs tilts and locks, with a lever or knob under the seat. Sit upright for typing, with the backrest close to vertical, and lean back for reading or a break. GABRYLLY lists a backrest that tilts from 90° to 135° and locks at 135°, so the upright end suits typing and the far end suits a break with the footrest out. If the chair will not lock, check that the tilt lever is pushed fully into its locked spot before assuming the mechanism is broken.

Set the armrests

Armrests should meet your forearms where they hang, so your shoulders stay relaxed and your elbows rest near your sides. Raise or lower them until your forearms rest level with the desk surface, and slide them inward or outward until they sit under your elbows without forcing your arms wide. GABRYLLY lists flip-up armrests that swing up 45° so the chair tucks under a desk when the arms are not in use, a handy trick in a small home office. If the armrests cannot reach desk height, lower the chair a little and add a footrest rather than hunching up to meet the arms.

Set the lumbar support and headrest

Lumbar support is the curve or pad in the lower backrest, and it should meet the small of your back, not your shoulder blades. Slide it up or down until it fills the hollow above your hips, then sit back against it instead of perching forward. The headrest is the last piece: GABRYLLY lists an adjustable 3D headrest, so set its height and angle until it meets the back of your head without pushing your chin down. When the headrest pushes you forward, lower it or tilt it back; when it hangs in the air behind you, raise it until it makes contact.

Use the footrest and check the fit

A pull-out footrest turns the chair into a lounger for breaks. GABRYLLY lists a steel footrest that extends up to 20.3 inches, and pairs it with a chair built for 8 to 10 hours of daily use. Check the fit against the listing too: the chair holds up to 300 lbs on a reinforced SGS Class 4 gas lift, with a 5-point base, overall dimensions of 27.5 in wide by 20.5 in deep by 46.8 to 55.5 in high, and a seat of 20.1 in wide by 20.5 in deep. If the chair still feels wrong after every control is set, the size may not suit you: a chair built for a taller frame will not adjust down to a shorter one, and the reverse holds too. Moving the chair takes some effort at 41.0 lb, so roll it on its casters rather than lifting it, and the 5-point base keeps it steady while you lean back. Assembly takes about 15 to 20 minutes with the included tools, per the listing, so set the chair up where it will live and adjust it there.

FAQ

How high should my office chair be?

High enough that your feet rest flat on the floor and your thighs sit roughly level, with your knees at or slightly below hip height. GABRYLLY lists a seat height of 19.2 to 23.7 in, a range the listing pairs with users from 5’5″ to 6’3″.

What angle should the backrest be set to?

Upright for typing, leaned back for reading or a break. GABRYLLY lists a backrest that tilts from 90° to 135° and locks at 135°.

Why does my office chair keep sinking?

The gas lift is the usual suspect: it holds the seat at the height you set, and when it wears out the seat slides down under weight. GABRYLLY lists a reinforced SGS Class 4 gas lift, and the chair holds up to 300 lbs on it. The guide to a chair that keeps going down covers the checks and the parts that usually need attention.

How long does it take to assemble an office chair?

It varies by chair. GABRYLLY lists about 15 to 20 minutes with the included tools and instructions, and a 3-year parts replacement term.

More for your workspace

See every Office Chairs and Seating guide, the office chair types guide, the office chair size guide and the best office chairs for working from home.