You settle in for a morning call, raise the seat to the right height, and by the time the call ends the chair has sunk back down to its lowest point. If you keep asking why does my office chair keep going down, the usual answer is the gas lift cylinder under the seat: the sealed unit that holds the chair up has lost pressure, so it can no longer hold its height under weight. The sections below show how to confirm that, how to measure the old cylinder, and which replacement cylinders match the common sizes.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
The quick answer
A chair that sinks slowly under weight, or drops as soon as you sit down, almost always has a worn gas lift cylinder. The cylinder is the sealed piston between the seat and the base, and once its seal leaks it cannot hold pressure. Check that the height lever still moves freely, then measure the old cylinder and replace it with one that matches the length, the top stem and the base fitting. The four cylinders below cover the common sizes, and each one states its travel and fit so the match can be checked before ordering.
Why does my office chair keep going down
The gas lift cylinder works as a sealed piston: gas pressure inside holds the seat at the height you set, and the lever opens a valve to let it move. When the seal wears, gas escapes and the pressure falls, so the seat sinks under weight and will not stay where you set it. A lever that feels loose or does nothing can point to the same part, since the valve sits at the top of the cylinder. Replacing the cylinder restores the lift, while the chair frame, seat and base can usually stay.
How to measure the cylinder before you buy
Measure the old cylinder before ordering a replacement, since the wrong length leaves the chair too high or too low. The listings here state the figures to match: the compressed and expanded lengths, the travel, the top stem and the base fitting. MASTERY MART states a 2 in (50mm) outer diameter and a 1-1/8 in (28mm) piston shaft, and tells buyers to measure the length of the outer cylinder before purchase. Krismose states a 9.6 in outer cylinder length, a 1.1 in top stem and a 2 in base hole, and warns that the chair may sit higher or lower than the original after fitting. Rythalix states a 5.5 in travel range from 11 to 16.5 in for top-activated chairs, and Omyoffice states 11.4 in compressed and 16.9 in expanded. Match all of the stated figures to the old part, and check whether the chair is top-activated or side-activated first: Rythalix states its cylinder is not for side-activated chairs.
Replacement cylinders for a sinking chair
The lift itself is the part to replace, and the four cylinders below are ranked by their Office Score, with the travel and fit figures from each listing so the right size can be matched to the old cylinder.
| # | Product | Office Score | Buy |
|---|---|---|---|
| 1 | Rythalix Gas Lift Cylinder | 9.8/10 | Buy on Amazon |
| 2 | MASTERY MART Gas Cylinder | 9.6/10 | Buy on Amazon |
| 3 | Omyoffice Gas Lift Cylinder | 9.6/10 | Buy on Amazon |
| 4 | Krismose Gas Lift Cylinder | 9.4/10 | Buy on Amazon |

Rythalix Gas Lift Cylinder
A top-activated Class 4 cylinder with 5.5 in of travel that handles the lift itself, for chairs whose old cylinder no longer holds height.
Pros
- 5.5 in travel, from 11 to 16.5 in
- 1000 lb capacity with Class 4 components stated
- Lifetime warranty with free replacement for manufacturing defects
- Installation gloves included, and 24/7 US-based support stated
Cons
- Only fits top-activated chairs; side-activated models are excluded
- Height guide covers 5 ft 7 in to 6 ft 2 in only
- No base diameter is stated for matching the chair base
- The 98% fit claim cannot be checked from the listing
Detailed Review
Rythalix lists this as a top-activated Class 4 cylinder with a 1000 lb capacity, a 5.5 in travel range from 11 to 16.5 in, and a 1-1/8 in (28mm) piston shaft. The maker says it fits 98% of top-activated chairs and suits heights from 5 ft 7 in to 6 ft 2 in, and includes installation gloves. The listing also states a lifetime warranty and 24/7 US-based support, and claims the cylinder runs at under 25dB and lasts 10+ years in high-wear spaces.
Who it's for: someone with a top-activated chair who wants the longest stated warranty here and a tall travel range. Who should skip it: anyone with a side-activated chair, or whose height falls outside the stated 5 ft 7 in to 6 ft 2 in guide.
Its Office Score of 9.8/10 comes from performance 32/35, build 22/25, value 21/25, safety 9/10 and warranty 4/5: 88 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Height range | 11 to 16.5 in |
|---|---|
| Travel | 5.5 in |
| Weight capacity | 1000 lb |
| Warranty | Lifetime |
Figures as published on the retailer listing, collected 12 November 2026. Performance figures are manufacturer rated.
Safety and Warranty
What this listing states. Class 4 components and an explosion-proof design are stated, with a 1000 lb capacity, so safety scores 9 of 10. Lifetime warranty: a free replacement is sent if the piston fails due to manufacturing defects. It does not say everything a buyer needs, such as who pays return shipping, so warranty scores 4 of 5. See How We Pick.
Fit and capacity. Check the stated seat height range against your desk height and the stated weight capacity against the heaviest user. Tighten bolts after the first week. Adjustments are comfort features, not treatment for pain; ask a clinician about any condition.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

MASTERY MART Gas Cylinder
A Class 4 cylinder with 4 in of travel that handles the lift replacement, with the compressed and expanded lengths stated so the fit can be checked before ordering.
Pros
- Exact compressed and expanded lengths stated: 9.88 in and 13.6 in
- BIFMA/ANSI standards and Class 4 construction stated
- 1000 lb capacity stated
- Outer diameter and shaft diameter both stated for fit checks
Cons
- No warranty term is stated
- 4 in travel is the smallest range in this group
- Title rounds the range to 9 to 13 in while the bullets give 9.88 to 13.6 in
- Not compatible with 1KEA and some other brands, per the listing
Detailed Review
MASTERY MART lists a Class 4 cylinder built to BIFMA/ANSI standards with a 1000 lb capacity, a 4 in stroke, and a 2 in (50mm) outer diameter with a 1-1/8 in (28mm) piston shaft. The title rounds the range to 9 to 13 in, while the bullets give the precise figures: 9.88 in compressed (251mm) and 13.6 in expanded (346mm), so use the bullet figures when measuring. The listing says to measure the length of the outer cylinder before purchase and notes it is not compatible with 1KEA and some other brands.
Who it's for: someone who wants exact compressed and expanded measurements to match against the old cylinder. Who should skip it: anyone who needs more than 4 in of travel, or who wants a stated warranty term.
Its Office Score of 9.6/10 comes from performance 29/35, build 21/25, value 21/25, safety 9/10 and warranty 0/5: 80 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Height range | 9.88 to 13.6 in |
|---|---|
| Travel | 4 in |
| Weight capacity | 1000 lb |
| Piston shaft | 1-1/8 in (28mm) |
Figures as published on the retailer listing, collected 12 November 2026. Performance figures are manufacturer rated.
Safety and Warranty
What this listing states. Manufactured to meet BIFMA/ANSI standards; Class 4 gas cylinder with a 1000 lb capacity, so safety scores 9 of 10. No warranty term, so warranty scores zero. See How We Pick.
Fit and capacity. Check the stated seat height range against your desk height and the stated weight capacity against the heaviest user. Tighten bolts after the first week. Adjustments are comfort features, not treatment for pain; ask a clinician about any condition.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

Omyoffice Gas Lift Cylinder
A 5.5 in travel cylinder that handles the lift replacement and reaches 16.9 in fully expanded, for chairs that need the taller end of the range.
Pros
- 5.5 in travel, from 11.4 to 16.9 in
- 1000 lb maximum weight stated
- Silent 360-degree rotation stated
- Lowest item weight here at 1.0 lb
Cons
- No warranty term is stated
- Claims 'official certification' but names no standard
- No shaft or base diameter is stated
Detailed Review
Omyoffice lists a 5.5 in travel cylinder, 11.4 in fully compressed and 16.9 in fully expanded, with a 1000 lb maximum weight and silent 360-degree rotation. The listing claims 'official certification' but names no standard, so there is no certification to score. The spec table lists the part number and model both as 1, which reads like placeholder data rather than a real part number.
Who it's for: someone who wants a tall expanded height and a light 1.0 lb part. Who should skip it: anyone who wants a named certification or a stated warranty term.
Its Office Score of 9.6/10 comes from performance 29/35, build 20/25, value 21/25, safety 5/10 and warranty 0/5: 75 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Height range | 11.4 to 16.9 in |
|---|---|
| Travel | 5.5 in |
| Weight capacity | 1000 lb |
| Item weight | 1.0 lb |
Figures as published on the retailer listing, collected 12 November 2026. Performance figures are manufacturer rated.
Safety and Warranty
What this listing states. Explosion-proof construction and a 1000 lb capacity are stated, so safety scores 5 of 10. No warranty term, so warranty scores zero. See How We Pick.
Fit and capacity. Check the stated seat height range against your desk height and the stated weight capacity against the heaviest user. Tighten bolts after the first week. Adjustments are comfort features, not treatment for pain; ask a clinician about any condition.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.

Krismose Gas Lift Cylinder
An alloy steel cylinder that handles the lift replacement, with the base hole, top stem and outer cylinder length stated for matching the old part.
Pros
- Tallest range here: 11.5 to 17 in
- Base hole, top stem and outer cylinder length all stated for matching
- Alloy steel build with a rust resistant coating
- Installs with common household tools, per the listing
Cons
- No weight capacity is stated
- No warranty term is stated
- No certification is stated
- The listing warns the chair may sit higher or lower than the original after fitting
Detailed Review
Krismose lists an alloy steel cylinder with a rust resistant coating, an 11.5 to 17 in range, a 2 in base hole, a 1.1 in top stem and a 9.6 in outer cylinder length, and says it installs with common household tools. No weight capacity is stated anywhere in the listing, which is the key figure for a part that holds the chair up. The listing warns that installing this part may make the chair higher or lower than the original, so the stated measurements need checking before ordering.
Who it's for: someone who has measured the old cylinder and matches the stated 9.6 in outer length, 2 in base hole and 1.1 in top stem. Who should skip it: anyone who needs a stated weight capacity or a warranty term.
Its Office Score of 9.4/10 comes from performance 27/35, build 20/25, value 19/25, safety 0/10 and warranty 0/5: 66 of 100 points, placed on our 9.2 to 9.8 scale.
Key Specifications
| Height range | 11.5 to 17 in |
|---|---|
| Outer cylinder | 9.6 in |
| Top stem | 1.1 in |
| Base hole | 2 in |
Figures as published on the retailer listing, collected 12 November 2026. Performance figures are manufacturer rated.
Safety and Warranty
What this listing states. This product does not plug in or run on a battery, so safety is not part of its score. No warranty term, so warranty scores zero. See How We Pick.
Fit and capacity. Check the stated seat height range against your desk height and the stated weight capacity against the heaviest user. Tighten bolts after the first week. Adjustments are comfort features, not treatment for pain; ask a clinician about any condition.
This is general buying information, not professional advice. Follow each product manual and local rules, and see our Safety Disclaimer.
As an Amazon Associate I earn from qualifying purchases.
FAQ
Why does my office chair sink when I sit on it?
The gas lift cylinder has lost pressure, so it can no longer hold the seat at the height you set. The cylinder is the sealed piston between the seat and the base, and a worn seal lets the gas escape.
Can a sinking office chair be fixed without replacing the cylinder?
The listings here treat the cylinder as the part to replace, and each one is sold as a direct replacement for the old piston. Measure the old cylinder and match the stated length, travel and fittings before ordering.
What size gas lift cylinder do I need?
Match the old cylinder’s compressed and expanded lengths, its travel, and the top stem and base fittings. The four cylinders here range from a 4 in stroke to a 5.5 in travel, with expanded heights from 13.6 in to 17 in.
Will a replacement cylinder fit my chair?
Check the activation type and the measurements first. Rythalix states its cylinder fits top-activated chairs and is not for side-activated chairs, MASTERY MART states a 2 in (50mm) outer diameter and a 1-1/8 in (28mm) shaft, and Krismose states a 2 in base hole and a 1.1 in top stem.
More for your workspace
See the Office Chairs and Seating guides, How to Disassemble Office Chair Step by Step and Office Chair Types: Which Style Fits Your Work.









