Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›

Home office gear, compared spec by spec.

Amazon Black Friday Week deals
Monitor Mounts, Keyboards and Mice

Laptop Stand Setup: Raise the Screen to Eye Level

A laptop stand setup raises the screen, frees desk space and keeps cables tidy, and this guide walks through measuring the laptop, setting the height and the angle.

Laptop Stand Setup: Raise the Screen to Eye Level

A laptop stand setup lifts the screen off the desk and puts it where you can see it without hunching over the keyboard, and it takes only a few minutes once the laptop and the desk are measured. The stand itself does the lifting, so the work is in choosing the right height, the right tilt and a spot on the desk where the base sits flat and the cables still reach. The steps below use the figures the makers publish for their stands, so you can match a stand to the laptop you own.

OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

The quick answer

Measure the laptop across the screen and check the weight the maker states, then pick a stand that lists a larger size range and a higher weight capacity than those figures. Set the stand so the top of the screen sits at or slightly below eye level, tilt it until the screen faces you squarely, and leave room behind the stand for the power cable and any hub. A separate keyboard helps when the laptop sits high, and a vented tray or an open frame lets air move under the laptop.

Laptop stand setup step by step

These moves cover the whole job: measure the laptop, set the height, set the tilt and swivel, then mount the stand and route the cables. Work through them in order, since each move depends on the figure checked in the move before it.

Step 1: Measure the laptop

Check the laptop size across the screen and the weight the maker states, then compare both against the range the stand lists. The BESIGN LS03 (on Amazon) lists laptops from 10 to 15.6 inches and a weight capacity of 8.8 lbs, while the OMOTON TM-L2 lists laptops from 10 to 17 inches and a capacity of 11 lbs. The WALI M00LP (on Amazon) lists a laptop up to 17 inches and a capacity of 22 lbs, and the OMOTON LA19 lists laptops from 10 to 15.6 inches with a capacity of 4 kg (8.8 lbs). The Rain Design mStand (on Amazon) lists laptops with depths less than 10.4 inches. Check the tray size too: the WALI tray measures 14 x 11 inches with a 0.6 inch lip at the front edge.

Step 2: Set the height

Raise the stand until the top of the screen sits at or slightly below eye level, then sit in the usual chair and check that the screen faces you without a long reach for the keys. The Rain Design mStand raises the screen by 5.9 inches, the BESIGN LS03 lifts the laptop by 6 inches and rises to 14.5 cm (5.7 inches), and the WALI M00LP lists a 16 inch height adjustment. The OMOTON LA19 adjusts from 0.79 inch to 4.72 inches, so it suits a low lift on a shallow desk as well as a higher lift for a taller chair. Non-adjustable stands give a single lift height; adjustable stands let you change the height when the chair or the desk changes.

Step 3: Set the tilt and the swivel

Tilt the tray until the screen faces you squarely and the glare from a window or a lamp drops away, then lock the angle if the stand has a lock. The WALI M00LP lists a tilt of plus or minus 15 degrees, a swivel of plus or minus 90 degrees and a rotation of 360 degrees, so it turns to face another chair or a client across the desk. Stands without a tilt control rely on the set angle of the tray. A rubber or silicone pad on the tray keeps the laptop from sliding as you type; the OMOTON LA19 lists soft silicone pads on the top platform and the base, and the BESIGN LS03 lists rubber on the holder arms.

Step 4: Mount the stand and route the cables

Clamp and grommet mounts hold the stand to the desk edge, while folding stands sit on the desk and pack away when the work is done. The WALI M00LP includes a C-clamp for desks from 0.4 inch to 4 inches thick and a grommet mount for desks from 0.4 inch to 2.2 inches thick, with mounting holes of 75 x 75 mm and 100 x 100 mm for a monitor. The OMOTON LA19 folds down to 0.7 inch (1.8 cm) for a bag, and the BESIGN LS03 comes apart in 3 steps for storage. Route the power cable through the hole behind the tray where the stand has a hole: the Rain Design mStand lists a cable hole 2 inches in diameter, and the WALI tray has venting holes that let air move under the laptop. Leave slack in the cable so the stand can tilt and swivel without pulling the plug.

What the listings state

Stand Screen lift Weight capacity Laptop size
BESIGN LS03 6 inches 8.8 lbs 10 to 15.6 inches
OMOTON LA19 0.79 to 4.72 inches 8.8 lbs 10 to 15.6 inches
OMOTON TM-L2 Not stated 11 lbs 10 to 17 inches
WALI M00LP 16 inches 22 lbs Up to 17 inches
Rain Design mStand 5.9 inches Not stated Less than 10.4 inches deep

Figures are manufacturer stated. Check the tray size and the desk thickness the mount needs before ordering.

Choosing between a non-adjustable stand and an adjustable stand

A non-adjustable stand suits a desk that never changes, while an adjustable stand suits a shared desk or a chair that moves up and down. The OMOTON LA19 adjusts from 0.79 inch to 4.72 inches and folds to 0.7 inch for travel, for a low desk, a tall chair and a bag. The WALI M00LP adjusts 16 inches in height and turns 360 degrees, for a sit-stand desk and a shared screen. A height-adjustable laptop stand is the safer pick when the chair height is still unsettled, and a stand that lifts to eye level keeps the screen where it belongs on a desk that never changes.

FAQ

What size laptop fits a laptop stand?

Check the size range the maker lists. The BESIGN LS03 and the OMOTON LA19 list laptops from 10 to 15.6 inches, the OMOTON TM-L2 lists laptops from 10 to 17 inches, and the WALI M00LP lists a laptop up to 17 inches. The Rain Design mStand lists laptops with depths less than 10.4 inches, so measure the laptop front to back as well as across the screen.

How high should a laptop stand raise the screen?

High enough that the top of the screen sits at or slightly below eye level. The Rain Design mStand raises the screen by 5.9 inches, the BESIGN LS03 lifts the laptop by 6 inches, the OMOTON LA19 adjusts from 0.79 inch to 4.72 inches, and the WALI M00LP lists a 16 inch height adjustment.

How much weight can a laptop stand hold?

Check the weight capacity the maker states. The BESIGN LS03 and the OMOTON LA19 list a capacity of 8.8 lbs, the OMOTON TM-L2 lists 11 lbs, and the WALI M00LP lists 22 lbs. Weigh the laptop with any sleeve or case still on it, since the stand carries the whole load.

Does a laptop stand need a clamp?

No. Folding stands sit on the desk with no clamp at all, while arm mounts clamp to the desk edge. The WALI M00LP includes a C-clamp for desks from 0.4 inch to 4 inches thick and a grommet mount for desks from 0.4 inch to 2.2 inches thick. Measure the desk edge before ordering a clamp mount.

Can I take a laptop stand when I travel?

Some stands fold flat. The OMOTON LA19 folds down to 0.7 inch (1.8 cm) and the BESIGN LS03 comes apart in 3 steps, so both pack into a bag. An aluminum stand such as the Rain Design mStand stays on the desk.

More for your workspace

See the best laptop stands for an external keyboard, the best laptop stands for a heavy laptop, the best laptop stands for cooling and the best monitor arms under 50.