A home desk can end up with a laptop, a desktop, a printer and a console all sharing the router, and the router may have no spare Ethernet port left. Learning how to use ethernet switch hardware solves that squeeze: plug the switch into power, connect it to the router with an Ethernet cable, then plug each device into the switch and check the port lights for a link. The steps below show how to place the switch, make each connection, and confirm the wired network is live.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
The quick answer
An unmanaged switch needs no software installation or configuration, according to the listings for the TP-Link and NETGEAR models. Plug the power adapter into the switch and an outlet, run an Ethernet cable from a LAN port on the router to any port on the switch, then run a cable from the switch to each device. The listing states that auto-negotiation senses the link speed, so the switch and each device agree on a speed without settings to change. Port lights show which links are live, and a device with no light needs its cable reseated or swapped for another cable.
Switch sizes at a glance
Switches in the listings come with 5, 8, 16 or 24 ports. The TP-Link LS1005G (on Amazon) listing describes 1 uplink port and 4 output ports, which shows how the uplink port goes to the router and the rest go to devices. The table below lists port counts and the dimensions the makers list for a few models, so the switch can be matched to the space on or under the desk.
| Model | Ports | Port speed | Size |
|---|---|---|---|
| TP-Link LS1005G | 5 | 10/100/1000 Mbps | 2.8 x 3.5433 x 0.9 in |
| NETGEAR GS305 | 5 | 1.0 Gbps | 6.2 x 4.0 x 1.1 in |
| NETGEAR GS308 | 8 | 1.0 Gbps | 6.22 x 4.02 x 1.02 in |
| TP-Link TL-SG116 | 16 | 10/100/1000 Mbps | 11.26 x 4.4 x 1.0 in |
| NETGEAR GS324 | 24 | 1.0 Gbps | 13.5 x 11.12 x 3.12 in |
Port speed matters as much as port count. The listings above show 10/100/1000 Mbps or 1.0 Gbps ports, while the TP-Link TL-SG105S-M2 (on Amazon) listing states 2.5-Gigabit ports with up to 25 Gbps of switching capacity. Match the switch to the cables in hand: the NETGEAR listings state the ports work with existing Cat5e or Cat6 Ethernet cables.
Step 1: Plug in power and place the switch
Set the switch where its cables can reach the router and each device without pulling taut, and where air can move around the case. The listings describe fanless designs, so the switch runs silent, and several models support desktop or wall-mount placement. The TP-Link TL-SG116 (on Amazon) listing states an operating temperature of 0 degree Celsius to 40 degree Celsius, or 32 degree Fahrenheit to 104 degree Fahrenheit, so a spot near a heat source is worth avoiding. Plug the power adapter into the switch and an outlet, then look for the power light.
Step 2: Connect the switch to the router
Run an Ethernet cable from a LAN port on the router to any RJ45 port on the switch. The TP-Link LS1005G listing describes 1 uplink port and 4 output ports, but on most unmanaged switches any port takes the router link, since the listing states the ports support Auto MDI/MDIX. Push the plug in until it clicks, then check that the port light for that connection is on. If the router sits in another room, route the cable along the wall or under the desk so it stays out of the walkway.
Step 3: Connect each device with an Ethernet cable
Plug a cable into a free port on the switch and the Ethernet port on the device, then repeat for each wired device at the desk, such as a desktop, a printer or a console. The NETGEAR listings state the ports work with Cat5e or Cat6 cables and auto-negotiate the link speed, so no setting needs changing on the switch. Keep the cable run tidy with labels if several cables share a path: the best cable labels with numbers make it plain which cable goes to which device.
Step 4: Check the lights and the connection
With power on and cables seated, each used port should show a link light. The listings describe IEEE 802.3X flow control for reliable data transfer, which keeps traffic moving after the link is up. Open a page or a stream on a wired device to confirm it reaches the network. If a port stays dark, reseat each end of the cable, try another port on the switch, and try another cable. If the device still shows no link, check the device network settings and confirm the cable is Cat5e or Cat6, since the NETGEAR listings state those cable types.
How to use ethernet switch with more devices
When the ports run out, add another switch rather than unplugging gear. Connect the new switch to a free port on the existing switch with an Ethernet cable, then move devices across. A 5-port switch linked to an 8-port switch gives the desk more wired ports, and the same plug-and-play setup applies: no software installation or configuration, according to the listings. For a larger room, the 16-port TP-Link TL-SG116 and the 24-port NETGEAR GS324 (on Amazon) give the desk room to grow, and each lists a fanless design with desktop or wall-mount placement. Keep the power plan in mind as well: a switch, a router and a modem each need an outlet, so a surge protector for a gaming setup can gather the plugs together.
FAQ
Does an ethernet switch need configuration?
No. The listings for the TP-Link and NETGEAR models describe unmanaged switches with plug-and-play setup and no software installation or configuration needed. Plug in power, connect the router, connect the devices, and the switch handles the rest.
Which port does the router plug into?
Any port works on an unmanaged switch. The TP-Link LS1005G listing describes 1 uplink port and 4 output ports, and the listing states the ports support Auto MDI/MDIX, so the router link can go in any port. Pick the port that keeps the cable run tidy.
How many devices can a switch connect?
Count the ports, then leave 1 port for the router link. The listings show switches with 5, 8, 16 or 24 ports, so a 5-port switch serves a small desk while a 24-port switch serves a room full of wired gear.
What cable does an ethernet switch need?
Use Cat5e or Cat6 Ethernet cable, which the NETGEAR listings state the ports work with. The TP-Link TL-SG105S-M2 listing states its 2.5-Gigabit ports run without a move to Cat6 wiring.
More for your workspace
See the best KVM switch with 8 ports, the best USB-C adapter for data transfer, the best KVM switch and the best HDMI splitter.





