Are all monitors compatible with monitor arms? No, not every screen fits every arm. The usual reason is a mismatch at the back of the screen, where the mounting holes do not line up with the plate, or a screen that is too wide or too heavy for the arm. This guide shows the checks that decide fit: the VESA hole pattern, the screen size and weight, and the desk edge where the arm mounts.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
The quick answer
Most flat and curved screens with VESA holes spaced 75x75mm or 100x100mm apart fit a standard arm, provided the screen sits inside the arm’s size range and weight limit. Screens with no VESA holes need an adapter, and screens above the arm’s weight limit need a heavier arm. Check the pattern, the size, the weight and the desk thickness before ordering, and the arm will fit.
Are all monitors compatible with monitor arms?
Compatibility comes down to four figures, and the table below shows how the arms in this guide compare. The common arms cover screens from 13 to 32 inches and weights from 4.4 to 19.8 lbs, with VESA patterns of 75x75mm and 100x100mm. Wider screens need the heavy duty class, which reaches 13 to 49 inches and 37.4 lbs. Warranties run from 2-year to 10-year terms across the arms in this guide.
| Arm example | Screen size | Weight limit | VESA pattern | Desk clamp |
|---|---|---|---|---|
| ErGear single arm | 13 to 34 inches | 4.84 to 19.8 lbs | 75x75mm, 100x100mm | 0.39 to 2.56 inches |
| HUANUO FlowLift | 13 to 32 inches | 4.4 to 19.8 lbs | 75x75mm, 100x100mm | 0.59 to 3.54 inches |
| ErGear heavy duty arm | 13 to 49 inches | Up to 37.4 lbs | 75x75mm, 100x100mm | 0.39 to 3.15 inches |
| VIVO AeroPoise | 17 to 32 inches | 4.4 to 19.8 lbs | 75x75mm, 100x100mm | Up to 3.1 inches |
A screen outside the size range or above the weight limit will not sit right on the arm, even when the holes line up.
Step 1: Check the VESA holes on the back of the screen
Look for mounting holes in a square pattern on the back of the screen. The arms in this guide use 75x75mm and 100x100mm patterns, and the ErGear single arm and the HUANUO arms list both patterns. If the screen has no holes, it needs a VESA adapter before it can mount; the PEGZONE arm (on Amazon) notes the same point, that a screen with no VESA holes needs an adapter. Measure the spacing between the holes when the pattern is unclear, and match it to the arm before ordering. The monitor mount screw size guide covers the thread sizes that go with each pattern.
Step 2: Check the screen size and weight
Size and weight decide the arm class. The HUANUO arms and the VIVO arm (on Amazon) cover 13 to 32 inches, or 17 to 32 inches for the VIVO arm, with weights from 4.4 to 19.8 lbs. The ErGear single arm stretches the range to 13 to 34 inches with a 4.84 to 19.8 lbs band, while the ErGear heavy duty arm reaches 13 to 49 inches and 37.4 lbs for ultrawide screens. Compare the screen weight with the arm’s limit: an arm rated below the screen weight will sag and will not hold its angle.
Step 3: Check the desk edge and the mount type
Arms mount with a C-clamp or a grommet base, and each mount fits a desk thickness range. The ErGear single arm clamps desks from 0.39 to 2.56 inches thick and takes a grommet base on desks from 0.39 to 2.95 inches thick. The HUANUO arms take desks from 0.59 to 3.54 inches thick, the ErGear heavy duty arm clamps desks from 0.39 to 3.15 inches thick, and the VIVO arm clamps tops up to 3.1 inches thick with a grommet mount for tops up to 1.9 inches thick. Measure the desk edge, check for beams or panels under the top that could block the clamp, and pick the mount that suits the desk.
Step 4: Handle a screen that does not fit
A screen with no VESA holes is not out of options: a VESA adapter adds the hole pattern the arm needs, and the best VESA monitor adapters guide compares the adapter options. A screen above the weight limit needs a heavier arm, such as the ErGear heavy duty arm at 37.4 lbs, rather than a stronger clamp. A screen wider than the arm’s range needs an arm built for ultrawide screens, such as the ErGear heavy duty arm at 13 to 49 inches. When the pattern, the size, the weight and the desk all line up, the arm fits and holds the screen where it belongs.
What to measure before you order
Write down the VESA pattern, the screen size, the screen weight and the desk thickness, then compare each figure with the arm you plan to order. The types of monitor mounts guide shows the arm styles to compare, and the dual monitor arm setup guide covers screens mounted side by side. When every figure lines up, the screen mounts on the arm and stays put.
FAQ
Do all monitors have VESA mounting holes?
No. Most desktop screens list VESA patterns of 75x75mm or 100x100mm, but some screens ship with no mounting holes at all. Check the back of the screen or the maker’s stated pattern before ordering an arm.
What size monitor fits a standard monitor arm?
The standard arms in this guide fit screens from 13 to 32 inches, with the ErGear single arm reaching 13 to 34 inches. Screens above that range need a heavy duty arm, such as the ErGear heavy duty arm at 13 to 49 inches.
How heavy a monitor can a monitor arm hold?
The standard arms in this guide hold screens from 4.4 to 19.8 lbs, with the ErGear single arm rated from 4.84 to 19.8 lbs. The ErGear heavy duty arm holds up to 37.4 lbs.
What if a monitor has no VESA holes?
A VESA adapter adds the 75x75mm or 100x100mm hole pattern to the back of the screen. The adapter has to match the arm’s pattern, so check both before ordering.
More for your workspace
See the types of monitor mounts, the monitor mount screw size guide, the best VESA monitor adapters and the dual monitor arm setup guide.





