A monitor arm that sags, slips or will not hold its angle usually has a worn or mismatched part, not a broken arm, and monitor arm parts are the pieces you swap to bring it back: the VESA plate, the desk clamp, the pole head, the extension arm and the screws that join them. This guide names each part, explains what it does and shows how to match a replacement to the arm and the screen you already own.
OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
The quick answer
Start with the VESA plate, since it sets the hole pattern the screen needs, then check the desk clamp, since it sets the desk edge the arm can grip. Match the pole head to the pole diameter and the screen weight, and add an extension arm only when the maker lists it for your arm series. The table below lists each part with the figures to check before ordering.
Monitor arm parts: what each part does
| Part | What it does | Figures to check |
|---|---|---|
| VESA plate | Bolts to the back of the screen and slides onto the arm head | 75x75mm and 100x100mm patterns; plate size 4.5 x 0.67 x 4.5 inches |
| Desk clamp | Grips the desk edge and holds the pole upright | Fits desks up to 3.25 inches, or 0.4 to 4 inches |
| Pole head | Carries the screen on the pole and sets tilt and rotation | Fits a 1.375 inch pole; screens up to 27 inches, 10 kg, 22 lb; tilt of 90 degrees, 360 degree rotation |
| Extension arm | Adds reach between the pole and the screen | Listed for the E6/W6 series arms |
| Screws and wrenches | Join the clamp, pole and plate | 6 x M4 screws, 4 x M6 screws, 2 x 5 mm and 2 x 4 mm hex wrenches |
Step 1: Match the VESA plate
Look at the hole pattern on the back of the screen and match it to the plate: the VIVO plate (on Amazon) covers 75x75mm and 100x100mm patterns, and the maker lists a 3 year warranty on the plate. The plate measures 4.5 x 0.67 x 4.5 inches, with a quick release bracket that lets the screen lift off the arm head. If the screen uses a pattern outside 75x75mm and 100x100mm, the plate will not fit, so check the monitor mount screw size guide for the thread sizes that go with it.
Step 2: Measure the desk edge for the clamp
Measure the thickness of the desk edge where the clamp will sit. The VIVO clamp fits desks up to 3.25 inches thick, and the maker lists a 3 year warranty on it, while the Yalikop clamp fits desks (on Amazon) from 0.4 to 4 inches thick and ships as a pack of 2 with 6 x M4 screws, 4 x M6 screws, 2 x 5 mm and 2 x 4 mm hex wrenches in the box. The Yalikop clamp also offers a grommet base for desks with a cable hole, which holds the pole with no drilling. Check the clamp jaw pads too: soft pads keep the desk surface free of dents and scratches.
Step 3: Match the pole head to the pole and the screen
The pole head has to fit the pole and carry the screen, so check both figures. The Suptek pole head (on Amazon) fits a 1.375 inch pole, carries a screen up to 27 inches and 10 kg, or 22 lb, and gives tilt of 90 degrees with 360 degree rotation. Mounting holes run 75x75mm and 100x100mm, so the head suits screens with either pattern. A head that fits the pole but is rated below the screen weight will sag, so match the weight figure before the tilt figure.
Step 4: Add reach with an extension arm
An extension arm sits between the arm and the screen to add reach, and it only works with the series the maker lists. The Ergounion extension (on Amazon) is listed for the E6/W6 series arms, and the maker states it is not compatible with other brands. Check the series name on your arm before ordering, since a mismatched extension will not join the pole. For arms that already reach far enough, skip the extension and spend the effort on the clamp and the plate instead.
Sizing notes
Write down the VESA pattern, the desk thickness, the pole diameter and the screen weight before you shop, and compare each figure with the part you plan to order. A clamp that fits the desk but not the pole, or a plate that fits the screen but not the head, leaves the arm half built. When the figures line up, the parts join with the screws in the box, and the arm holds its angle through the workday. For a wider view of arm styles, see the types of monitor mounts and the dual monitor arm setup guide.
FAQ
What VESA patterns do monitor arm parts use?
The VIVO plate and the Suptek pole head cover 75x75mm and 100x100mm patterns. Check the hole pattern on the back of the screen before ordering a plate or a head.
How thick can a desk be for a replacement clamp?
The VIVO clamp fits desks up to 3.25 inches thick, while the Yalikop clamp fits desks from 0.4 to 4 inches thick. Measure the desk edge and pick a clamp whose range covers it.
What size screen can a pole head carry?
The Suptek pole head carries a screen up to 27 inches and 10 kg, or 22 lb. Match both the screen size and the screen weight to the head before ordering.
Does an extension arm fit any monitor arm?
No. The Ergounion extension is listed for the E6/W6 series arms and is not compatible with other brands, so check the series name on your arm and order an extension listed for that series.
More for your workspace
See the types of monitor mounts, the monitor mount screw size guide, the best VESA monitor adapters and the dual monitor arm setup guide.





