Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›

Home office gear, compared spec by spec.

Amazon Black Friday Week deals
Monitor Arms and Stands

Monitor Setup for Gaming: Stands, Arms and Placement

Monitor setup for gaming, with how to match an arm or riser to your screen size, weight and VESA pattern, set the height and tilt, and tidy the cables.

Monitor Setup for Gaming: Stands, Arms and Placement

The game loads, the screen sits too low, and the keyboard has nowhere to go because the monitor base eats the desk. A good monitor setup for gaming starts with the mount, not the monitor: the screen at eye level, the keyboard clear of the stand and the cables out of the way. This guide walks through monitor setup for gaming in four steps: check the screen size, weight and VESA pattern, pick an arm or a riser, set the height and tilt, and mount it with the cables tidy. Every figure below comes from a monitor arm or stand listing, including one that disagrees with itself.

OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

Monitor setup for gaming: the quick answer

Match the mount to the monitor first: screen size, weight and VESA pattern. A single arm suits one screen, a dual arm suits two screens side by side, and a riser suits a screen that stays put while the desk gains storage and ports. Set the top of the screen at or slightly below eye level, tilt it so the middle of the screen faces your eyes, and run the cables through the clips or the hub.

Monitor arms and stands at a glance

Mount Fits screens Holds VESA pattern
ErGear Single Monitor Arm 13-34 in 4.84-19.8 lb 75x75mm, 100x100mm
HUANUO FlowLift Single Monitor Mount 13-32 in 4.4-19.8 lb 75x75mm, 100x100mm
AX WABER Single Monitor Arm 13-32 in 4.4-20 lb 75x75mm, 100x100mm
GRIFEMA Dual Monitor Arm 13-32 in 19.8 lb each arm 75x75mm, 100x100mm
Afaloona RGB Monitor Arm 13-27 in 4.4-17.6 lb 75x75mm, 100x100mm

The table covers arms. Risers are a different shape: the Petify stand holds 72 lb, the Klearlook riser holds 55 lb and the Razer stand supports up (on Amazon) to 44 lb. Arms clamp to the desk and move the screen; risers sit on the desk and lift it to one set height.

Step 1: Check the screen size, weight and VESA pattern

Measure the monitor before you shop for a mount. Check the size first: the arms here fit 13 to 34 inch screens, with the ErGear arm (on Amazon) covering the widest range. Check the weight next: the ErGear arm holds 4.84 to 19.8 lb, the HUANUO arm (on Amazon) holds 4.4 to 19.8 lb, the AX WABER arm (on Amazon) holds 4.4 to 20 lb and the Afaloona arm (on Amazon) holds 4.4 to 17.6 lb. The GRIFEMA dual arm holds 19.8 lb on each arm, or 9 kg per arm as the listing also states.

Check the VESA pattern on the back of the monitor: every arm here fits VESA 75x75mm and 100x100mm, so measure the four mounting holes and match them to the pattern. The AX WABER listing gives two ranges: 17 to 32 inch screens and 4.4 to 22 lb in one place, and 13 to 32 inch screens and 4.4 to 20 lb in another. Measure the screen yourself before you order.

Step 2: Pick an arm or a riser

A single arm suits one screen that moves: tilt, swivel and rotation let you change the angle for gaming or work. The ErGear arm tilts +80 degrees to -50 degrees, swivels ±90 degrees and rotates 360 degrees, with height adjustment up to 17.5 inches and reach up to 18.1 inches. The HUANUO arm tilts -50 degrees to +85 degrees, swivels ±90 degrees and rotates 360 degrees, and lifts the screen up to 39.6 cm from the desktop. The AX WABER arm tilts -45 degrees to +90 degrees, swivels ±90 degrees and rotates 360 degrees, extends out 19.3 inches and raises up to 17.3 inches. A monitor arm in this range covers most single-screen gaming setups.

A riser suits a screen that stays put. The Petify stand adjusts from 16.1 to 21.7 inches wide, holds 72 lb and adds a drawer, a phone holder and a 4-port USB hub with three USB 2.0 ports and one USB 3.0 port. The Klearlook riser adjusts to 16.5, 18.5 or 20.5 inches wide, holds 55 lb and adds a drawer and a tablet and phone holder, with 18.09 inches between the legs for a keyboard. The Razer stand supports up to 44 lb and adds a 4-port hub with HDMI 2.0. A monitor stand lifts the screen while the desk gains storage and ports.

A dual arm suits two screens side by side. The GRIFEMA dual arm fits 13 to 32 inch screens, holds 19.8 lb on each arm, rotates 360 degrees, tilts ±90 degrees and swivels ±90 degrees, with reach up to 16.54 inches. Each arm moves on its own, so set the main screen straight ahead and the other at an angle.

Step 3: Set the height, tilt and swivel

Set the height first. The top of the screen should sit at or slightly below eye level, so you look slightly down at the middle of the screen. A riser lifts the screen to one set height, so check the stand against your eye level before you buy.

Set the tilt next, then swivel the screen so it faces you from an angle. Tighten the tension to match the monitor weight: the HUANUO listing says to adjust tension according to your monitor weight.

Step 4: Mount it and tidy the cables

Clamp or bolt the arm to the desk, then hang the monitor on the plate. The ErGear arm sets up in three easy steps with a tool-free VESA mount, the HUANUO arm sets up in 3 minutes and the GRIFEMA dual arm sets up in 15 to 20 minutes. The AX WABER arm offers a C-clamp or grommet mount for tabletops 0.4 to 2.7 inches thick.

Run the cables through the clips or the hub. The ErGear arm has cable clips that open with no tools, and the GRIFEMA arm has built-in cable management. A cable management kit for a monitor arm keeps the rest of the slack off the desk.

RGB lighting and warranties

The Petify stand has 10 RGB lighting modes with one control button, the Afaloona arm has RGB lighting, and the Razer stand supports 16.8 million colors. Warranties run 2 years on the ErGear arm, the Petify stand and the Razer stand, 5 years on the HUANUO arm, 1 year on the Klearlook riser and 90 days on the AX WABER arm.

FAQ

What size monitor fits a monitor arm?

The arms here fit 13 to 34 inch screens: the ErGear arm covers 13 to 34 inches, and the HUANUO, AX WABER and GRIFEMA arms cover 13 to 32 inches. Measure the screen and match the VESA pattern too.

How much weight can a monitor arm hold?

Check the arm listing. The ErGear arm holds 4.84 to 19.8 lb, the HUANUO arm holds 4.4 to 19.8 lb and the GRIFEMA dual arm holds 19.8 lb on each arm. Stay inside the listed range.

Do I need a C-clamp or a grommet mount?

It depends on the desk. A C-clamp grips the desk edge, and a grommet mount needs a hole in the desk. The ErGear clamp fits desks 0.39 to 2.56 inches thick, the GRIFEMA clamp fits 0.39 to 3.15 inches, the ErGear grommet base fits 0.39 to 2.95 inches and the HUANUO grommet mount fits 0.59 to 3.54 inches.

Should I pick a monitor arm or a monitor riser?

Pick an arm when the screen needs to move: tilt, swivel and rotation change the angle. Pick a riser when the screen stays put and the desk needs storage, ports or RGB: the Petify riser adds a drawer and a 4-port hub, and the Klearlook riser adds a drawer and a tablet and phone holder.

Can a monitor arm hold an ultrawide monitor?

Check the size and weight limits. The ErGear arm fits 13 to 34 inch flat or curved monitors up to 19.8 lb, and the Klearlook riser holds up to 55 lb. Measure the screen before you buy.

More for your workspace

See the best monitor arms, the best dual monitor stands, the best full-motion monitor mounts and the best acrylic monitor risers.