Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›

Home office gear, compared spec by spec.

Amazon Black Friday Week deals
Monitor Arms and Stands

Monitor Setup Guide: Arms, Stands and Positioning

How to set up a monitor at eye level: check the screen size, weight and VESA pattern, pick an arm that fits the desk, then set the height and angle.

Monitor Setup Guide: Arms, Stands and Positioning

Monitor setup means placing the screen so the top sits at or slightly below eye level, about an arm’s length away, with the screen tilted slightly back and the desk clear underneath. A monitor that sits too low or too far to the side turns a workday into a long stretch of looking down or twisting sideways, while a monitor on an arm frees the desk surface for a keyboard, a notebook and a docking station. The steps below cover checking the monitor, checking the desk, mounting the arm and setting the height and angle, using figures from monitor arm listings.

OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

The quick answer

Start with the monitor: note the screen size, the weight and the VESA mounting pattern on the back. Then check the desk: the thickness, whether the edge can take a C-clamp, and whether a grommet hole is available. Pick an arm whose stated size range, weight capacity and VESA patterns cover the monitor, and whose clamp range covers the desk. Mount the arm, attach the monitor to the VESA plate, then set the height so the top of the screen sits at or slightly below eye level and tilt the screen until the view is comfortable.

Monitor setup at a glance

Arm Screen size Weight capacity VESA pattern Desk clamp
ErGear single arm 13 to 34 in 4.84 to 19.8 lbs 75×75, 100×100 mm C-clamp 0.39 to 2.56 in
HUANUO FlowLift 13 to 32 in 4.4 to 19.8 lbs 75×75, 100×100 mm 0.59 to 3.54 in
5Rcom single arm 13 to 35 in 4.4 to 22 lbs Not stated Not stated
ErGear ultrawide 13 to 49 in 37.4 lbs 75×75, 100×100 mm C-clamp 0.39 to 3.15 in
WALI M001XL 13 to 34 in Up to 22 lbs 75×75, 100×100 mm 3 in thick desk
VIVO AeroPoise 17 to 32 in 4.4 to 19.8 lbs 75×75, 100×100 mm C-clamp up to 3.1 in

Figures as stated in each listing. Screen size, weight capacity and VESA pattern must all match the monitor, and the clamp range must match the desk.

Step 1: Check the monitor

Screen size, weight and VESA pattern decide whether an arm fits. Screen sizes in these listings run from 13 in to 49 in, with most single arms covering 13 to 32 in or 13 to 34 in screens and the ErGear ultrawide arm covering 13 to 49 in screens. Weight capacities run from 4.4 to 19.8 lbs on most arms here, while the 5Rcom arm (on Amazon) and the WALI arm (on Amazon) hold up to 22 lbs and the ErGear ultrawide arm holds 37.4 lbs. Every arm here except the 5Rcom lists VESA patterns of 75x75mm and 100x100mm, so check the hole pattern on the back of the monitor before buying. Read the listing carefully: the AX WABER arm (on Amazon) titles a 17 to 32 in fit and 22 lbs capacity while its bullets state 13 to 32 in and 4.4 to 20 lbs, so the title and the bullets disagree. When figures disagree, ask the maker or pick an arm whose figures are consistent.

Step 2: Check the desk

Most arms here mount with a C-clamp on the desk edge or a grommet base through a hole in the desktop, and some offer both. Desk thickness ranges in these listings run from 0.39 in to 3.54 in: the ErGear single arm clamps desks 0.39 to 2.56 in thick and fits grommet bases 0.39 to 2.95 in thick, the HUANUO arm supports 0.59 to 3.54 in, and the VIVO arm (on Amazon) clamps tops up to 3.1 in thick with a grommet mount for tops up to 1.9 in thick. The WALI arm fits a 3 in thick desk with a 3.5 in diameter grommet base. Measure the desk thickness at the edge where the clamp will sit, and check that the underside is free of beams or panels that would block the clamp, as the HUANUO listing advises. A grommet mount needs a hole in the desktop or a spare grommet opening; a C-clamp needs a clear edge. A monitor stand is the alternative when the desk cannot take a clamp at all.

Step 3: Mount the arm

Mounting follows the same order on the arms here: clamp the bracket to the desk, attach the monitor to the VESA plate, then adjust the tension to the monitor weight. The HUANUO arm states installation in 3 minutes in 3 steps with all necessary hardware included, and the ErGear single arm states setup in three easy steps with a tool-free VESA plate. Tighten the clamp firmly, then hang the monitor and check that the arm holds its position before letting go. Route the cables through the clips or channels on the arm so they do not snag when the screen moves; the ErGear, 5Rcom and WALI arms all list cable management on the arm.

Step 4: Set the height and angle

Raise the screen until the top sits at or slightly below eye level, then tilt it until the view is comfortable from a normal seated position. Height adjustment on the arms here reaches up to 17.5 in on the ErGear single arm, up to 17.7 in on the 5Rcom arm and up to 22.2 in on the ErGear ultrawide arm, while the HUANUO arm lifts the screen up to 39.6 cm from the desktop and the AX WABER arm lifts it up to 44 cm. Reach runs up to 18.1 in on the ErGear single arm and up to 21.2 in on the 5Rcom and ErGear ultrawide arms, so the screen can sit closer or further back without moving the desk. Tilt ranges vary: the ErGear single arm tilts +80 to -50 degrees, the HUANUO FlowLift tilts -50 to +85 degrees, the 5Rcom arm tilts -45 to +90 degrees and the ErGear ultrawide arm tilts +30 to -40 degrees. Swivel runs to plus or minus 90 degrees on most arms here, the VIVO arm swivels 180 degrees, and rotation runs to 360 degrees, so a screen can turn from landscape to portrait. Set the tension so the arm stays where it is put: the HUANUO arm states it remains stable at any angle without extra work. A monitor arm with this range of motion covers most desk layouts without a second mount.

Choosing an arm for a standard monitor or an ultrawide

A standard monitor suits any of the single arms here, while an ultrawide screen needs the wider range of the ErGear ultrawide arm, which fits 13 to 49 in screens and holds 37.4 lbs. An ultrawide monitor arm with a dual C-clamp spreads the load for extra stability, as the ErGear ultrawide listing describes. The WALI arm adds height for a tall setup: its pole runs 31.5 in high, and its mount fits screens up to 34 in at up to 22 lbs. Warranty terms in these listings run from 90 days on the AX WABER arm to 10 years on the WALI and ErGear ultrawide arms, with 1 year on the 5Rcom arm, 2 years on the ErGear single arm, 3 years on the VIVO arm and 5 years on the HUANUO arm. A longer stated term is no promise about a single unit, but it shows how long the maker is willing to stand behind the arm.

FAQ

What size monitor fits a single monitor arm?

Most single arms here fit 13 to 32 in or 13 to 34 in screens. The 5Rcom arm fits 13 to 35 in screens, and the ErGear ultrawide arm fits 13 to 49 in screens. Check the stated size range before buying, since a screen outside the range may not balance on the arm.

How much weight can a monitor arm hold?

Most arms here hold 4.4 to 19.8 lbs. The 5Rcom arm and the WALI arm hold up to 22 lbs, and the ErGear ultrawide arm holds 37.4 lbs. Check the monitor weight against the stated capacity before buying.

What do VESA 75×75 and 100×100 mean?

They are the mounting hole patterns on the back of a monitor, measured in millimetres: 75x75mm and 100x100mm. Every arm here except the 5Rcom lists the 75x75mm and 100x100mm patterns, so check which pattern the monitor has before buying.

Will a monitor arm fit my desk?

Check the desk thickness against the clamp range: the ErGear single arm clamps desks 0.39 to 2.56 in thick, the HUANUO arm supports 0.59 to 3.54 in, and the VIVO arm clamps tops up to 3.1 in thick. The underside must be free of beams or panels that would block the clamp.

How long does it take to install a monitor arm?

The HUANUO arm states installation in 3 minutes in 3 steps, and the ErGear single arm states setup in three easy steps with a tool-free VESA plate. Allow extra time for routing cables and setting the tension to the monitor weight.

More for your workspace

See the monitor arms, the monitor stands, the standing desks, the office chairs, the keyboard trays and the under-desk footrests.