Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›

Home office gear, compared spec by spec.

Amazon Black Friday Week deals
Gaming Chairs

Gaming Chair Parts: Replacement Options Explained

Gaming chair parts, from the 28 inch base to the gas lift cylinder and tilt mechanism, with the mounting holes, stroke and socket sizes to measure before ordering.

Gaming Chair Parts: Replacement Options Explained

A chair that sinks by noon turns a morning call into a slow slide toward the floor, and gaming chair parts are the answer, not a new chair. Gaming chair parts are the replaceable pieces that hold a gaming chair together: the base, the gas lift cylinder, the tilt mechanism, the armrests, the casters, and the angle adjuster that sets the backrest. This guide names each part, shows how to match it to your chair, and explains what to measure before you order.

OfficeKitHQ earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

The quick answer

Most gaming chair repairs come down to a short list of parts. The base and its casters carry the chair, the gas lift cylinder sets the seat height, the tilt mechanism controls lean and lock, the armrests set the arm height, and the angle adjuster sets the backrest. Match the mounting holes, the cylinder size and the caster socket before ordering, and check each measurement against the listing.

Gaming chair parts: what each part does

Use this table to name the part you need, then read the steps for its measurements.

Part What it does Check before ordering
Base Carries the chair on its legs and casters 28 inch diameter, 2 inch center hole, 11 by 22 mm caster sockets
Gas lift cylinder Raises and lowers the seat Class 3, 278 mm long, 403 mm extended, 125 mm stroke (4.9 inch)
Tilt mechanism Controls lean and locks the seat angle Mounting holes 10.2 by 6 in, 0.12 in steel bracket, 500 lbs
Armrests Support the arms at the sides of the seat 4D adjustment, sold as a pair
Casters and glides Roll the chair or hold it still 5 casters, 11 by 22 mm sockets, bell glides for a fixed base
Back support rod Joins the backrest to the seat frame 29 by 26.5 by 3.5 cm, 5.6 by 40 mm screws
Angle adjuster Sets the backrest angle 180 degree range, 11.22 by 9.44 by 1.57 in

Every figure in the table comes from a listing in the reference set for this guide. Brands appear below only where a figure is cited, and your chair may use different measurements, so measure the part you are replacing before ordering.

Step 1: Find the broken part

Start with what the chair does wrong. A seat that sinks on its own points to the gas lift cylinder. A chair that wobbles or leans points to the base or the tilt mechanism. Armrests that wobble or sit uneven point to the armrest brackets. A backrest that will not hold its angle points to the angle adjuster or the back support rod. Casters that drag or stick point to the wheels themselves. Name the symptom, then match the part in the table above. The gaming chair repair guide walks through the same symptoms with more detail.

Step 2: Measure the mounting holes

The tilt mechanism bolts to the seat through a set of mounting holes, and the spacing decides whether a replacement fits. Besitu lists mounting holes at 10.2 inches long by 6 inches wide for its 500 lbs tilt mechanism, and Frassie lists mounting hole spacing of 10 by 6 inches for its base sets. The figures differ, so measure your own chair: take the distance between hole centers across the length and across the width, and compare both figures with the listing before ordering. Besitu also warns to check the bolt pattern and measure the seat mechanism size before ordering.

Step 3: Match the cylinder

The gas lift cylinder is the part that raises and lowers the seat, and it is also the part behind a chair that sinks. Frassie lists a Class 3 cylinder at 278 mm long with a 403 mm extension length and a 125 mm stroke, listed as 4.9 inch. The stroke is the travel between the lowest and highest positions the listing states. Besitu lists its tilt mechanism as accepting standard Dia. 28mm (1.1-Inch) tapered gas lift cylinders, so check the diameter your mechanism takes as well as the length. See why a chair keeps going down for the sinking symptom in more detail.

Step 4: Match the base and casters

The base sets the footprint of the chair. Frassie lists a 28 inch base diameter on its metal and nylon base sets, and the red nylon set lists a standard center hole of 2 inch. The caster socket size is 11 by 22 mm on the listings that state it, so check your own base sockets before ordering wheels. Frassie offers 5 silent rubber casters and 5 bell glides in the set, so you can choose a rolling base or a fixed base. The nylon base lists a load-bearing capacity of up to 500 lbs, and the metal base set lists a 28 inch steel base with the same 10 by 6 inch mounting hole spacing. For more wheel options, see the chair casters and glides guide.

Step 5: Armrests, back rod and angle adjuster

Armrests come as a pair and adjust in 4 dimensions on the Kei Project listing, which names DXRacer, Secret Lab and Gtracing as fits, along with other main brand gaming chairs. The back support rod from KH866 measures 29 by 26.5 by 3.5 cm, with 3 pieces of 5.6 by 40 mm screws, 3 flat washers and a 5.6 mm hex wrench in the box, and fits most standard gaming, executive and office swivel chairs. Check the listing’s own measurements first: the KH866 bullets list 29 by 26.5 by 3.5 cm while its spec table lists 10.0 by 2.0 by 8.0 inches, so the size entries do not agree. The Veemoon angle adjuster (on Amazon) lists a 180 degree range at 11.22 by 9.44 by 1.57 inches, and suits gaming and office chairs as a replacement for a worn regulator. See the gaming chair elbow pads guide for armrest padding options.

FAQ

What part makes a gaming chair sink?

The gas lift cylinder. Frassie lists a Class 3 cylinder at 278 mm long with a 403 mm extension length and a 125 mm stroke, listed as 4.9 inch, and a worn cylinder is the usual cause of a sinking seat. Besitu lists its tilt mechanism as accepting standard Dia. 28mm (1.1-Inch) tapered gas lift cylinders.

What size are gaming chair base mounting holes?

Besitu lists 10.2 by 6 inches for its tilt mechanism, and Frassie lists 10 by 6 inches for its base sets. Measure your own chair, since the listings differ, and check the bolt pattern before ordering.

Can I replace just the casters on a gaming chair?

Yes. Frassie lists base sets with 5 silent rubber casters and 5 bell glides, and lists the caster socket size as 11 by 22 mm. Check your base sockets against that size before ordering wheels.

What does 4D mean on gaming chair armrests?

It means the armrests adjust in 4 dimensions. Kei Project lists its replacement armrests as fully adjustable in 4 dimensions, sold as a pair, and lists DXRacer, Secret Lab and Gtracing as fits.

More for your workspace

See every gaming chairs guide and all seating guides, plus how to disassemble an office chair and how to adjust an office chair.